timtheenchanteruk

timtheenchanteruk

Well-Known Member
now, I have googled this and not got any definitive, or helpful answers.

Got me gauge, got me sender, but where the chuff do I put it??

Is there a spare port somwhere for it?
Or do I need to cut into the oil cooler lines and insert a T, if so whick one, top or bottom, and where would I get such a T??

Ive had a quick look, but cant see anything obvious, the injector pump kinda gets in the way.
 
is there a port in the side of the mount?? Can't 100% see, but there again, not sure just where im looking, I presume on the front of it (as apposed to where the cooler pipes exit.

I can see an indent, or somthing here, is it a blank???
 
found a piccy of the mount...

$T2eC16J,!yEE9s5jDYT9BR4nHPIqjg~~60_12.JPG


the "indent" I can see is the one at the front of the pic.
 
Had to unscrew the existing 'dash light' sender and put in a t-piece on mine

Was a bit tight in terms of working space but doable - think i had to extend the existing sender wire too

Can send piccys if needed early evening - pm me if required as in office just now
 
If you have a look at the front end of the housing there should be a hex head which is approx 19mm AF. Remove that and there should be a fairly coarse thread which the sender screws into.

I found it on mine by accident! :D
 
timtheenchanteruk said:
now, I have googled this and not got any definitive, or helpful answers.

Got me gauge, got me sender, but where the chuff do I put it??

Is there a spare port somwhere for it?
Or do I need to cut into the oil cooler lines and insert a T, if so whick one, top or bottom, and where would I get such a T??

Ive had a quick look, but cant see anything obvious, the injector pump kinda gets in the way.
Click to expand...

What gauge did you get and where are you going to mount it?

Thanks.
 
I might do this. Oil temp and oil pressure would be nice for advance warning of impending implosions.

Ed
 
I got mine of ebay, canbt remember what make right now, but mines moutned under the dash, just in front of the gear stick, just fits nicely, will get a pic on if I get a mo.
 
Don't forget, oil pressure can be taken off a remote adaptor but oil temp needs to be taken as close to the block as possible otherwise the reading will be false (photo of Tee-piece & guage is for pressure).
 
natas said:
yes please.
Click to expand...

here you go...

DSC_0016.jpg


the gear stick is clost, but doesnt foul it, I was looking at aftermarket dashes, but TBH, they all look too bolt on to me, the pod looks better I think.

Im going to be putting the clock in there, and oil pressure. got fuel, water temp and voltmeter already in the dash.
Where the clock is is getting a standard plate (that I already have) that Ill get punched out for some more switches. :)
 
Yes I do actually. Was going to stick a clock in it, but an oil pressure guage would be more use!

Ed
 
You must log in or register to reply here.

Similar threads

A
1984 109 FFR 24v oil temp gauge issues
Replies
1
Views
441
layfin
L
Padda.116
300TDI Disco1, temp sensor locations
Replies
9
Views
631
resto_d1
R
G
Oil pressure switch thread ?
Replies
2
Views
243
grewth
G
Ric82
Series 3 Smiths Oil Pressure Guage Electrical
Replies
4
Views
710
Ric82
Ric82
R
300tdi Temp guage
Replies
13
Views
2K
dag019
dag019