Dobbs · Jan 20, 2014

So here's a challenge. I was changing the timing belt on my 12J 2.5 NAD at the weekend. I'd already bought the timing pointer for the flywheel window - as I'd seen the flywheel window and have no bottom plug hole.

But, when turning the crank to fit the timing pointer, I noticed the flywheel was a more modern version with a timing notch rather than EP markings!!. Of course the notch is for the timing plug that fits into the drain hole.

So it looks like I've got a newer flywheel, in an older flywheel housing. With no EP mark, or drain plug hole how do I find TDC?

Cheers

flat · Jan 20, 2014

could you take a glow plug out cylinder number one, put your thumb over it and feel for the compression stroke of the cycle while slowly turning the engine over via the crank bolt. then mark the flywheel accordingly?

I did that with a petrol engine once, i dont know if the glowplug hole will fit a thumb though lol, do you have any children as they have smaller fingers lol

Disconnect the starter solenoid!

Dobbs · Jan 20, 2014

flat said:
could you take a glow plug out cylinder number one, put your thumb over it and feel for the compression stroke of the cycle while slowly turning the engine over via the crank bolt. then mark the flywheel accordingly?!

Possibly, but doesn't sound that accurate.

Dr_evil · Jan 20, 2014

remove the rocker cover, rotate the crank pulley until the inlet starts to drop then rotate again until the exhaust starts to drop, measure the distance between and measure the distance between then half it

flat · Jan 20, 2014

Dobbs said:
Possibly, but doesn't sound that accurate.

no but gets you in the right area though maybe?

Dobbs · Jan 20, 2014

Dr_evil said:
remove the rocker cover, rotate the crank pulley until the inlet starts to drop then rotate again until the exhaust starts to drop, measure the distance between and measure the distance between then half it

Measure the distance between? The crank position?

James1966 · Jan 20, 2014

used a dial guage down injector hole or plug hole before, just put a piece of bar down the most vertical hole and wait till guage stops, that should do the trick, get it close by using the rockers first.

Dr_evil · Jan 20, 2014

Dobbs said:
Measure the distance between? The crank position?

yeah between the two points, stick some paper to it then mark it at each point

Kwakerman · Jan 20, 2014

The correct way to do it is with a degree wheel attached to the crank (with a pointer attached to the block) and a depth gauge / DTI or similar down the plug hole.
1. Turn crank until No 1 piston is roughly at TDC (use use depth gauge to feel when piston stops rising.
2. Set the degree wheel / pointer so it reads 180 degrees (it doesn't actually need to be 180 but it will make the sums easier than if using zero)
3. Make a note of the figure (180)
4. Turn the crank clockwise until the piston drops exactly 15mm according to depth gauge.
5. Make a note of degree wheel number (say 200 as an example)
6. Turn crank anticlockwise back over TDC until depth indicator reads 20mm
7. Slowly turn crank clockwise until exactly 15mm is shown on depth gauge.
8. Make a note of degree wheel number (say 166 as an example)
9. Subtract '8' from '5' (use your actual figures) In this example 200 - 166 = 34
10. Divide '9' answer by 2 (34/2 = 17)
11. Now turn the crank clockwise by the answer to '10' (using the degree wheel) In this example 166 + 17 = 183
12. When the degree wheel reads 183 the No1 piston is at exactly TDC (the actual figure is irrelevant, it is just used to get the crank in the correct position).

Obviously accuracy is important when measuring the depth.

jamesmartin · Jan 20, 2014

Dobbs said:
So here's a challenge. I was changing the timing belt on my 12J 2.5 NAD at the weekend. I'd already bought the timing pointer for the flywheel window - as I'd seen the flywheel window and have no bottom plug hole.

But, when turning the crank to fit the timing pointer, I noticed the flywheel was a more modern version with a timing notch rather than EP markings!!. Of course the notch is for the timing plug that fits into the drain hole.

So it looks like I've got a newer flywheel, in an older flywheel housing. With no EP mark, or drain plug hole how do I find TDC?

Cheers

they arent timed tdc but exhaust peak 108 degrees btdc ,just use mark on front of crank pulley and arrow on rear case

Dobbs · Jan 20, 2014

jamesmartin said:
they arent timed tdc but exhaust peak 108 degrees btdc ,just use mark on front of crank pulley and arrow on rear case

Ah. should have thought of that before I put the cover back on. I guess the timing marks on the pulleys would have given me the right spot.

jamesmartin · Jan 20, 2014

Dobbs said:
Ah. should have thought of that before I put the cover back on. I guess the timing marks on the pulleys would have given me the right spot.

as i said they arent timed at tdc so that wont help you ,hole for timing pin should be above cover if fitted for timing pointer

Dobbs · Jan 22, 2014

jamesmartin said:
hole for timing pin should be above cover if fitted for timing pointer

Yes, nearly. It's about 10cm out. I can see the hole/slot for the pin whizz past when rotating the crank, but it stops about 10cm past the timing pointer cover. Otherwise, timing marks, and fuel pump are all lined up.

Mark22_2 · Jun 27, 2019

Dobbs said:
Yes, nearly. It's about 10cm out. I can see the hole/slot for the pin whizz past when rotating the crank, but it stops about 10cm past the timing pointer cover. Otherwise, timing marks, and fuel pump are all lined up.

Hi, I know it's a long time ago but did you get this sorted?
My 12j has a tiny slot in flywheel but no pointer.

I'm timing to the manual but still refuses to start!

Dobbs · Jun 29, 2019

Hi, yes. I kind of ignored it until I took the front timing cover off. When I saw the timing marks all line up at front I was less worried about the flywheel.

Mark22_2 said:
Hi, I know it's a long time ago but did you get this sorted?
My 12j has a tiny slot in flywheel but no pointer.

I'm timing to the manual but still refuses to start!

Dobbs

Active Member

flat

Well-Known Member

Dobbs

Active Member

Dr_evil

Banned

flat

Well-Known Member

Dobbs

Active Member

James1966

Active Member

Dr_evil

Banned

Kwakerman

Well-Known Member

jamesmartin

Well-Known Member

Dobbs

Active Member

jamesmartin

Well-Known Member

Dobbs

Active Member

Mark22_2

Member

Dobbs

Active Member

Similar threads