JonnyP

JonnyP

Well-Known Member
I have me another 200 tdi engine and lt 77 gearbox to put in my disco. I have been searching for answers all afternoon and got me a load of info but I could still do with some more info.

Can I remove the engine and gearbox together (using a decent crane), or do they need to be split..?

What parts would it be a good idea to replace while doing the job..? I will get a new clutch kit, but is there anything else..?

I think I now have all the basic info for doing the job, but any advice would be welcome :)
 
Oil seals and core plugs on the engine, timing belt. A hd clutch fork oil in box and tbox
 
The one on the back of the engine is most important as once it is in you can't get to it!!

Probably a good idea to de-grease and steam it too while it'son the floor as it'll make leaks easier to locate later on.

Might be an idea to change the Tbox output seals too as much easier when you can stand over then as opposed to laying under them.
 
Half wish I never asked now lol.. The engine I am putting in is out of another car and I was not intending to open it up..
 
Finally getting onto this job soon..
Just ordered up a quality clutch kit, hd release fork, crankshaft oil seal and a timing belt kit including both pulleys.
I need to get me a clutch aligning tool, can anyone tell me if this will do the job, or do I need a better one..? CLUTCH MATE UNI CLUTCH ALIGNING TOOL STK.NO.52329 | eBay

I was told not to touch the core plugs unless they are leaking, so I don't know what to do about them..?
I am borrowing a crane off a mate and I still need to get all the fluids..

Anything else I might need..?
 
you can do the clutch by eye, or if the other lt77 is scrap, then cut the input shaft off and use that.
 
trax said:
you can do the clutch by eye, or if the other lt77 is scrap, then cut the input shaft off and use that.
Click to expand...
Old one is not scrap, I might try n recondition it. Good to know I can do it by eye though, I have only ever done one clutch before n that was a mk 11 cortina and I didnt know anything about aligning tools n it was a bitch to do..
Pikey said:
I use one of these and never have a problem with any of the clutches I've fitted.

1x Clutch Alignment Tool 4 piece multi-fit clutch mandrel Hand & Power Tools | eBay

Might be worth changing the clutch slave cylinder while ya doing everything else.. They is cheap as chips..
Click to expand...
Cheers Pikey, will get a new slave n push rod. Did I read once that its good to tie on the end of the push rod..?
 
JonnyP said:
Old one is not scrap, I might try n recondition it. Good to know I can do it by eye though, I have only ever done one clutch before n that was a mk 11 cortina and I didnt know anything about aligning tools n it was a bitch to do..

Cheers Pikey, will get a new slave n push rod. Did I read once that its good to tie on the end of the push rod..?
Click to expand...

well, there's always umming and arring if you do it by eye. for the price, i'd just buy the tool :)
 
Hello guys,

On the subject of changing clutch...
How do you remove the top bolt on the gearbox cos its a fecker to get to?

Cheers
 
You must log in or register to reply here.

Similar threads

findo1
Engine or gearbox in first ? Which is best?
Replies
2
Views
288
findo1
findo1
Dieselweasel0
Discovery lt77 gearbox
Replies
5
Views
407
lynall
L
P
As a query how difficult is it to replace engine to gearbox seal as it appears I have leaks around the engine sump and gearbox to engine.
Replies
3
Views
638
tilly2
T
S
LAND ROVER DISCOVERY 3.0L 306DT I WANT TO FIT A GEN 1 ENGINE INTO A GEN 2
Replies
1
Views
272
lynall
L
Maat
Disco 2 Torque converter won't go in all the way
Replies
8
Views
1K
kevstar
kevstar