M

mikehump

New Member
Help!

I have a 1988 Defender 90 soft top with two piece doors and sliding windows. My left hand internal door catch has broken. I tried to buy a new one but they are apparently not made any more. Does anybody have any suggestions as to what I can do? I am getting a little sick of opening my window every time I want to open my door !

Below is a picture of the offending piece and the replacement that I was sent (which obviously doesn't fit!)
Defender door catch.jpg

Thanks in advance,

Mike
 
you did well to get the replacement that you have that one fits mine, early 90 pre defender.

I couldn't find one to buy anywhere eventually got 1 fabricated and then put the old linkage back on.

Can you not take swap the linkage or is it thelinkage that is broke
 
Cavey_P38 said:
you did well to get the replacement that you have that one fits mine, early 90 pre defender.

I couldn't find one to buy anywhere eventually got 1 fabricated and then put the old linkage back on.

Can you not take swap the linkage or is it thelinkage that is broke
Click to expand...


Unfortunately it is the little bar that holds the linkage that has broken. You can just see it in this photo (the bronze coloured part). The bar and link in the replacement part is not interchangable :-(


I may have to take the thing apart and try to get someone to fabricate a new metal bar.

LR catch 2.jpg
 
Bit leftfield but could you swap the door lock/handle for a series version and do away with the door card and broken handle mechanism
 
That inner handle is for an early 90/110 with windup windows.
Iv not seen that arrangement on your door. Most would just have lift up handles.
Do you have door cards ?
Thanks
 
Thanks for the comments/thoughts, most appreciated!
LR door cards.jpg


I seem to have quite a rare door configuration?
I do indeed have door cards. This is a picture of the door card and catch.
Swapping for a series handle and door cards might work but I'm not sure if the catch is the same? I can take a more detailed photo if that would help?
 
Rare door....not seen any like this
So can you remove the flat bar & replace with the old rod?
Handle looks the same in the picture.
 
v8250 said:
Guys,something in the back of my mind thinks these are Morris Marina internal door locks. They were used across a myriad of vehicles, are still readily available from Marina, MGB and Mini suppliers and are cheap as chips.

https://www.ebay.co.uk/itm/MGB-MGBG...226588?hash=item23e402885c:g:a~EAAOSw5eBfjL1W

eta: though may be barking up wrong tree
Click to expand...

I'm pretty sure you're right - same door handle in lots of old british vehicles - the MGB one looks identical. I can vouch for the fact that the outer trim is the same - the part number even matches!
 
Believe might also be found in a sherpa van..

I had a quick search when i broke mine round our local scrap yards and gave up, got on fabricated in metal for MOT having driven it for months and opened the window to open the outside handle..lol

Swapped the fabricators labour for use of our workshop ramp over a weekend...top result love a bit of barter

That is a very unusual door card i must say looks a bit of a cross between a series and an early 90 /110
 
You must log in or register to reply here.

Similar threads

mjr92
Rear sliding side windows
Replies
1
Views
306
julianf
julianf
dag019
Are all door latches equal?
Replies
2
Views
343
dag019
dag019
Kevlandau
Defender Door lock
Replies
19
Views
2K
Kevlandau
Kevlandau
dag019
Difference between hard top and station wagon roof
Replies
9
Views
437
julianf
julianf
MAF Diver
Disco 2 Nanocom/RAVE manual is wrong: adjusting windows after removing key and opening a door?
Replies
4
Views
443
MAF Diver
MAF Diver