A

AMDS42

New Member
Hello,

I have the SLS and Off-road lights on but no fault on the nanocom.

The Leveling button doesn't work and doesn't do any sound ( No "bounng")
The SLS looks to work well but I noticed that when I stop at a traffic light, the valve open 1 second and immediately after the compressor run 2 second so the back of the car goes slighty down and immediately after goes up.

I test valves and compressor on both sides with the nanocom and all is good.

Could you please help ?
Maybe I changed a setting on the nanocom, I don't remember but could be that the lights appeared after I played with the nanocom but not sure...

Thanks a lot for your help
best
Amaury
 
Hi, unfortunately nanocom used to miss SLS codes even if they are logged, only hawkeye is 100% reliable with these... btw, did you play with nanocom in the BCU settings?

you should try to run a calibration on it.... rise it as to be at even level all around then store those heights
 
Thanks a lot for your swift answer,
I have already use the fonction in nanocom to setup new height and it worked I am sure they have been saved,
I don’t have Hawkey , may I ask you more suggestion?I don’t understand why as soon as I break to zero kilometre the valve open and immediately after the compressor starts , could be default of height sensor?
And yes I played with the BCU but I don’t remember what I changed
Thanks
 
AMDS42 said:
I don’t understand why as soon as I break to zero kilometre the valve open and immediately after the compressor starts , could be default of height sensor?
Click to expand...
1. is the vehicle fitted with ACE?
2. this SLS activity while braking happens all the time?... if you dont know exactly try to slow down gently as the vehicle to not lean forward at all, see what happens then and report.
 
sierrafery said:
1. is the vehicle fitted with ACE?
2. this SLS activity while braking happens all the time?... if you dont know exactly try to slow down gently as the vehicle to not lean forward at all, see what happens then and report.
Click to expand...
I will test that,
I see your point I think the same that there is a link with ACE sensor issue and it could be a good idea because 3 months ago I had the ACE light which appear and was remaining for 1 month and disappeared alone after 1 month. so no ACE light on the dashboard now only SLS and Offroad are on, and ACE is working well in speed hard turn the disco remain horizontal
 
So I perform the test, the output is not easy,
. If I stop without using the break to maintain the attitude sometime I have the valve followed by the compressor , sometime the compressor followed by the valve and the compressor again, . But I found something interesting if I forward and I stop the valve run and after the compressor . If I reverse and I stop it is first the compressor without a valve opening. And it is related to the speed because it occurred forward and reverse when I arrive under 3 or 4 Km/h, is this help for your disgnostic? Thanks again for your help best
 
Disconnect the battery, swap the two sensors around, give contact spray to theyr's connectors then recalibrate and see if someting changes or not... if no change the ECU becomes suspect, as you have nanocom better change it cos good sh ones are not so expensive
 
You must log in or register to reply here.

Similar threads

B
D2 sls compressor not running
Replies
8
Views
1K
sierrafery
sierrafery
Vagabondrobb
Disco 2 SLS again
Replies
9
Views
830
sierrafery
sierrafery
L
XYZ switch and no front electric windows. Help!
Replies
18
Views
754
sierrafery
sierrafery
S
The four amigos and fault 85
Replies
3
Views
505
Spuddo
S
SullyUk
Disco 2 ACE faults
Replies
16
Views
529
sierrafery
sierrafery