E

Ed Watson

New Member
Hi all,

I am trying to start a 1997 Discovery NAS with the V-8. The vehicle was owned by a Land Rover enthusiast who sadly, died a couple of years ago. His distraught widow left the car sitting in the drive for a year, at which point I volunteered to get it going and sell the truck, along with a tonne of parts. It's been a bigger job than I anticipated. The vehicle started twice and ran strong, at which point I thought I had it beat. Hah! The joke's on me. The trouble codes indicate it's alarm/immobilizer issue. I have changed the battery, changed the battery in the key fob, tried entering an EKA code without success, disconnected the battery and then reconnected it with the key in position two .. and a host of other things.
Among the guys parts is a Hawkeye diagnostic tool that I recently discovered. I have successfully connected it and tried to disable the alarm and immobilizer. But for some reason the Discovery's computer won't take the changes. It asks me if I want to save the changes, I say yes, but nothing is saved. Any ideas why?
Thanks
 
Ed Watson said:
Hi all,

I am trying to start a 1997 Discovery NAS with the V-8. The vehicle was owned by a Land Rover enthusiast who sadly, died a couple of years ago. His distraught widow left the car sitting in the drive for a year, at which point I volunteered to get it going and sell the truck, along with a tonne of parts. It's been a bigger job than I anticipated. The vehicle started twice and ran strong, at which point I thought I had it beat. Hah! The joke's on me. The trouble codes indicate it's alarm/immobilizer issue. I have changed the battery, changed the battery in the key fob, tried entering an EKA code without success, disconnected the battery and then reconnected it with the key in position two .. and a host of other things.
Among the guys parts is a Hawkeye diagnostic tool that I recently discovered. I have successfully connected it and tried to disable the alarm and immobilizer. But for some reason the Discovery's computer won't take the changes. It asks me if I want to save the changes, I say yes, but nothing is saved. Any ideas why?
Thanks
Click to expand...
That would simply indicate a dicky starter motor to me. Cover the basics first.
 
Hi -- the codes are P1622 "wrong security codes received by the ECM in sequence" and P1621 "Communications with the Security ECM has not happened..."
 
Ed Watson said:
Hi -- the codes are P1622 "wrong security codes received by the ECM in sequence" and P1621 "Communications with the Security ECM has not happened..."
Click to expand...
IMO you have to replace the alarm ECU with confirmed working same part number one cos everything points to that unit unless it's a wiring issue on that path
 
Ed Watson said:
Hi all,

I am trying to start a 1997 Discovery NAS with the V-8. The vehicle was owned by a Land Rover enthusiast who sadly, died a couple of years ago. His distraught widow left the car sitting in the drive for a year, at which point I volunteered to get it going and sell the truck, along with a tonne of parts. It's been a bigger job than I anticipated. The vehicle started twice and ran strong, at which point I thought I had it beat. Hah! The joke's on me. The trouble codes indicate it's alarm/immobilizer issue. I have changed the battery, changed the battery in the key fob, tried entering an EKA code without success, disconnected the battery and then reconnected it with the key in position two .. and a host of other things.
Among the guys parts is a Hawkeye diagnostic tool that I recently discovered. I have successfully connected it and tried to disable the alarm and immobilizer. But for some reason the Discovery's computer won't take the changes. It asks me if I want to save the changes, I say yes, but nothing is saved. Any ideas why?
Thanks
Click to expand...
The link below may be of interest to you although the are more available, as I expect you have the 4.0 or 4.6 engine fitted to your disco, and if so then I believe that the security system is coded specifically to the vehicle, which will add a additional issue if you wish to try a replacement.

With your Hawkeye kit, if its suitable for your vehicle then it may just require a firmware/software update to work fully, although there’s also other diagnostic tool to use if not.

www.landyzone.co.uk

P38 alarm/immobiliser removal

Hi all, I have a year 2000 P38 with the 4.6 Bosch engine. The battery died and she's totally immobilised herself! Got a few things to try today, including getting the EKA code from my local dealer. My question is, does anyone in the North Shields/Newcastle area have the equipment to remove...
www.landyzone.co.uk www.landyzone.co.uk
 
discool said:
With your Hawkeye kit, if its suitable for your vehicle then it may just require a firmware/software update to work fully,
Click to expand...
AAMOF Hawkeye works quite well with the '97 V8 D1 as it is, the gist is that no diagnostic tool would work as long as the vehicle is immobilised which is the case here so the only chance i see is to replace the alarm ECU, should be programmable with Hawkeye as long as the replacement unit was not removed from immobilised vehicle and the circuit is intact, did it myself for a friend albeit it was not a NAS spec which according to the WSM might be a bit different as it seems they dont even have the EKA code feature.
 
I'm new to Land Rovers, so I don't know if all the NAS vehicles didn't have the EKA code feature. But on this one the security card number has 5 digits, not 4 (radio maybe?) and when I try to enter an EKA code there is no recognition of any kind from the Disco. It's possibly a door lock micro switch problem, as the truck sat outside for months in the rain and the door lock sometimes sticks. I'll try that first. Then perhaps the alarm ECU, if I can find one. Hah, what I find perplexing is that the thing started repeatedly one day, then nothing the next day.
 
Ed Watson said:
It's possibly a door lock micro switch problem, as the truck sat outside for months in the rain and the door lock sometimes sticks.
Click to expand...
AA...ha... you should have said that from the beginning, that's very relevant cos if the fob does not unlock and the door's key switch doesnt work the system is not remobilised by anything as it's still in locked condition , do you have only one fob or two and none of them is working?
 
The fob works, and locks and unlocks the car, but the drivers side lock sometimes sticks and I have to either unlock it with the key, or reach around and pull the lock up manually. I'll pull the door panel off and take a look. Thx again.
 
You must log in or register to reply here.

Similar threads

J
Help.. stuck in superlock alarm
Replies
2
Views
252
Landmark2
Landmark2
P38 guy
P38 immobilizer
Replies
15
Views
1K
Grrrrrr
Grrrrrr
O
Disco 2 immobiliser/central locking issues
Replies
8
Views
329
Shedload
S
M
Td5 immobilised after battery change
Replies
4
Views
666
Landmark2
Landmark2
B
Freelander 2 central locking
Replies
0
Views
297
Bobdude
B