mutsnutz

mutsnutz

Well-Known Member
Hi folks my x reg range rover 2.5 overheated tonight think the head might be cooked had to drive it in limp mode for a few miles to get of duel carriage way my question is apart from gasket what else part wise do I need to replace head I have a good spare in shed
 
Not sure it was fine ran ok up until I hit duel carriage way and then temp went through the roof and it boiled its tits off oil is ok had new water pump on and stat
 
mutsnutz said:
Not sure it was fine ran ok up until I hit duel carriage way and then temp went through the roof and it boiled its tits off oil is ok had new water pump on and stat
Click to expand...

Duff stat?

Guess you might get some pointers when you get the head off.
 
Do I need new head bolts when I put it back together possibly be a duff stat I will stick another in it and change the viscous fan and rad with my spare ones it doesn't overheat when ticking over sit all day on tick over temp at middle
 
mutsnutz said:
Do I need new head bolts when I put it back together possibly be a duff stat I will stick another in it and change the viscous fan and rad with my spare ones it doesn't overheat when ticking over sit all day on tick over temp at middle
Click to expand...

New head bolts would be good. And new cam bolt, not totally needed but better safe than sorry. You will need several special tools.
 
What special tools do I need wammers I have the cam and flywheel locking tools what else is needed
 
mutsnutz said:
What special tools do I need wammers I have the cam and flywheel locking tools what else is needed
Click to expand...

Top chain tensioner retractor and pin to hold tensioner back. Angle gauge for head bolts. Torque wrench. Gaskets.
 
Last edited:
Thanks wammers do I need to change the chains 160thousand on the clock but no starting issues
 
Just had a read up on whats involved in doing the job and I think its beyond my skill set so going to put it in mates garage and pay him the money and get the job done right
 
mutsnutz said:
Just had a read up on whats involved in doing the job and I think its beyond my skill set so going to put it in mates garage and pay him the money and get the job done right
Click to expand...

A good man always knows his limitations. Lots would bite off more than they can chew and cock it up.
 
Not 100% but going to try a different stat viscous fan and rad if it does it again then I think it most likely to be the head it ticks over great temp gauge sits in the middle it will sit like that for hours no problem I was driving it around for over two hours before it boiled
 
From my bitter experience ,have the head pressure tested ,even the one in the garage before it goes on. I had my valves vacuum checked for sealing .Make sure you use a quality head gasket loads of cheap ones about
best of luck
 
You can bet everything will be checked and double checked just to make sure it doesnt happen again
 
I agree, head gasket quality is a serious must!! It's a lot of work to get to the point were you realise the gasket is duff!!!
good luck. ;)
 
You must log in or register to reply here.

Similar threads

MikeFl4
P38A Possible coolant in oil
Replies
9
Views
837
Datatek
Datatek
stemac33
P38A Range Rover P38 2.5 dt for sale
Replies
2
Views
2K
stemac33
stemac33
Bustrucket
Disco 2 Td5 Overheating
Replies
3
Views
682
johnlad
johnlad
jimmacD
Back to the P38 house of pain!
2
Replies
21
Views
2K
Grrrrrr
Grrrrrr
Kerlaan
Freelander 1 Propshaft carrier bearings - how long to change them? [SOLVED]
Replies
6
Views
902
Kerlaan
Kerlaan