Discodevon

Discodevon

Well-Known Member
hello I have footwell rust in my td5 defender, It’s at the normal place where the bulk head meets the floor where the metals are sandwiched together, it’s not structural but want to catch it before it does, question is what to treat it with after wire brushing?
 
I slathered mine with the thin and runny variety of Dinitrol (ML3125) which seems to have sufficient corrosion inhibiting powers even after it has dried to keep the rust at bay. Everything looks black and inert rather than orange and active. Each time I have the floors up (e.g. clutch changes, gearbox work etc) I put some more on. No discernable rust progress in the last six years.
 
Thank you lads much appreciated, any know a good red lead/ oxide? It’s a tad flaky on the edges so will need to clean that up first before I apply anything
 
lead oxide paint was banned eons ago, if i'm not mistaken due to the COSHH rules
The 'red oxide' paint nowdays is just a pigment colour but with none of the lead, which is pointless.
Better off with zinc paint from Bilt Hamber. It's offers way better protection from rust.
 
I used the same stuff 2 years ago on my footwells although they were new welded ones. I haven't painted them since, just bare red oxide and no rust at all. Underside has thick paint on top. Could just be paddocks coating underneath but still good.
 
Last edited:
windy81 said:
lead oxide paint was banned eons ago, if i'm not mistaken due to the COSHH rules
The 'red oxide' paint nowdays is just a pigment colour but with none of the lead, which is pointless.
Better off with zinc paint from Bilt Hamber. It's offers way better protection from rust.
Click to expand...

Not all red oxide is just a colour. The Tor Coatings stuff I used is a zinc rich primer, it just so happens that it is coloured red like the days of old. The 5ltr container weighed over 20kg, so it must have had a decent amount of zinc.
 
So I have rusty holes on the 45 degree slope part where it meets the flat part of the foot well, they're not big but I can see through them. Is it a case of cutting out just that strip or buying new foot wells?

If so are paddocks the best place to get them?
 
Muppetdaze said:
So I have rusty holes on the 45 degree slope part where it meets the flat part of the foot well, they're not big but I can see through them. Is it a case of cutting out just that strip or buying new foot wells?

If so are paddocks the best place to get them?
Click to expand...

I would get them from YRM, but that’s personal choice.

It depends on the state of the rest of the steel work as to how much you need to cut out and replace. You can’t weld to rust, so you will need to find decent steel to weld the new panels to.
 
Muppetdaze said:
So I have rusty holes on the 45 degree slope part where it meets the flat part of the foot well, they're not big but I can see through them. Is it a case of cutting out just that strip or buying new foot wells?

If so are paddocks the best place to get them?
Click to expand...
What age is your defender?
 
20190214_073811.jpg
20190214_073841.jpg

Here is my footwells, 90 is kept outside. Looks good after 2 years. Not good that after 2 years they are still in red oxide. Got them from paddocks.
 
You must log in or register to reply here.

Similar threads

D
Td5 defender vibration
Replies
11
Views
397
bankz5152
bankz5152
200tdi Land Rover 90
Defender TD5 2003 idle problems!
Replies
5
Views
1K
Anaconda
A
R
First post and need opinion on possible defender purchase
Replies
12
Views
2K
RustyDefender
RustyDefender
S
1988 90 replacing lights with LEDs and have lots of questions
Replies
5
Views
861
sleepybear
S
Bustrucket
Disco 2 Td5 Overheating
Replies
3
Views
785
johnlad
johnlad