J

james0211

New Member

• May 25, 2013

• #1

would love to hear peoples points views and ideas on this

ok so the bane of some landy owners life is the heater, not the best in the world
i know, some peoples are better than others but hay ho mines not that good


any way i do a lot of work with WOLF LR's and it wasn't until recently i noticed that they kick out a lot more hot air out of the blowers than my LR my mates and a fair few others i jumped in.

so a grabbed a normal 12 volt heater blower and put 24 volts through it and it nearly blow me out the work shop.

these are the combinations i tried

12v motor with 12v input stranded nothing special

12v motor with 24v input awesome

24v motor with 12v felt just like the 12volt blower with 12volt input

24v motor with 24v input awesome

does any one know if the motors are the same???

so i think with a little more testing i am going to find a way to put 18-24volts through my blower so i can drive around in my pants

 

bellabuster

New Member

• May 25, 2013

• #2

And a fire extinguisher in the cab

 

matchmetisse

New Member

• May 25, 2013

• #3

12v motor and 24v: burnt out motor

 

PaulMc

Active Member

• May 25, 2013

• #4

24V into a 12V blower motor may not be as daft and as dangerous as it sounds.

Have a read through this thread - A better defender heater - a new project! - Tools and Fabrication - LR4x4 - The Land Rover Forum

.

 

Hippo

Lord Hippo

• May 25, 2013

• #5

If the motor int rated to take 24v then it shouldn't be powered oft 24v. If it's 12v then that's all it should be powered from. May work for the time being but later on it won't like it.

 

J

james0211

New Member

• May 26, 2013

• #6

PaulMc said:

24V into a 12V blower motor may not be as daft and as dangerous as it sounds.

Have a read through this thread - A better defender heater - a new project! - Tools and Fabrication - LR4x4 - The Land Rover Forum

.

Click to expand...

seems to me that there are some mixed views on this idea, think some more testing is required,
worse case i will get a 24v motor and use that instead

 

Disc300Series

Active Member

• Jan 2, 2016

• #7

james0211 said:

would love to hear peoples points views and ideas on this

ok so the bane of some landy owners life is the heater, not the best in the world
i know, some peoples are better than others but hay ho mines not that good


any way i do a lot of work with WOLF LR's and it wasn't until recently i noticed that they kick out a lot more hot air out of the blowers than my LR my mates and a fair few others i jumped in.

so a grabbed a normal 12 volt heater blower and put 24 volts through it and it nearly blow me out the work shop.

these are the combinations i tried

12v motor with 12v input stranded nothing special

12v motor with 24v input awesome

24v motor with 12v felt just like the 12volt blower with 12volt input

24v motor with 24v input awesome

does any one know if the motors are the same???

so i think with a little more testing i am going to find a way to put 18-24volts through my blower so i can drive around in my pants

Click to expand...

Howd you

 

Disc300Series

Active Member

• Jan 2, 2016

• #8

Thanks howd youget on with using 24 volts ? Where can I get a 24v motor ?

 

Kwakerman

Well-Known Member

• Jan 2, 2016

• #9

As the OP hasn't been on LZ since 2013 I don't think you will get an answer from him. Don't think 24v motor cures the issue, if it did everyone would be raving about it (and they are not). A defender heater can be made to work reasonably well (my 300 one does). Need to make sure engine is running at the correct temp, don't trust LR gauge as they are useless. My original sat at mid position which I thought was fine until I fitted a VDO gauge / sender which actually indicated 70 degrees. Ended up that Tstat was stuck open, fitted new one and temp read 90 and heater actually works well. Also go around and sort out all drafts and seals as that helps too.

 

Disc300Series

Active Member

• Jan 7, 2016

• #10

I ask only because my defender is all 24Volt except my blower so need a 24 volt motor. Thanks

 

zeaphod

Well-Known Member

• Jan 7, 2016

• #11

You could buy a 24v bilge blower - cheaper and more powerful.