Alpinewoodsman

Alpinewoodsman

Well-Known Member
Early 90.
I've got far too much play on the CV joints- both sides. The CV joints, swivel housings and bearings were replaced by a specialist 4x4 garage two years ago, and have under 10,000km on them, so I'd really hope they're not dead already.

Is there sensible way to reduce play on these joints without a full replacement?
 
KISSMYAURA said:
u sure its not your drive flanges?
Click to expand...
Fairly sure. They seemed good when I checked end float ( all four wheels) and the rear ones were now impeccable.

And I had it up on a lift- test guy used the hydraulic axle lift to load/unload it, and I could see the vertical movement around the swivel housing as they did.
 
The only adjustments, shims at the top swivel joint. How do you know you have CV joint wear ? If it is general slap in the drive train more likely it is the diff.
 
tottot said:
The only adjustments, shims at the top swivel joint. How do you know you have CV joint wear ? If it is general slap in the drive train more likely it is the diff.
Click to expand...
The front wheels rock vertically if you lift them off the ground and apply some force, so if that's the diff, I've got bigger problems than I thought!
 
Sounds like it is the swivel pins or the wheel bearings. Have someone else rock the wheel while you watch from behind. If housing moves on the ball housing it's swivel pin. If housing is still and only wheel / disc moves it's bearing that needs tightening.
 
Two bolts on the top with a brake pipe, remove them, lift out the pin, remove a shim and reassemble. From memory...you may have to keep the hub pushed in at the top, towards the diff or the swivel oil will leak out. To do the free play properly you need a spring scale to check resistance and add or remove shims to get it right. I had an issue where those top two bolts kept coming loose and giving me the play that you have but lock tight sorted that.
 
Alpinewoodsman said:
The front wheels rock vertically if you lift them off the ground and apply some force, so if that's the diff, I've got bigger problems than I thought!
Click to expand...
It's not the diff. It's hub bearings if the wheel rocks when held at 3 and 9 AND 6 and 12 o clock. If rocking is only at 6 and 12 then it's top pin wear/ adjustment or just loose bolts on the top pin like I had.
 
With the top pin out you need a jack under the housing to stop it dropping down and letting oil out. Will only drop a bit but enough to let the oil out.
 
tottot said:
Sounds like it is the swivel pins or the wheel bearings. Have someone else rock the wheel while you watch from behind. If housing moves on the ball housing it's swivel pin. If housing is still and only wheel / disc moves it's bearing that needs tightening.
Click to expand...
Swivel pins it is. I could see the housing move on the lift at 6 and 12. 3 and 9 is fine- I'd done end float on the bearings all round and fixed that...
Right, park it on the flat ( hard work round here) wheel off, spare jack ready for the housing, and hope it is just loose bolts on the top pin.
 
Given the low milage you have done since your garage did the work that all they did was remove some shims and perhaps fit a new swivel pin, but I doubt very much a new swivel pin bush was fitted. Unless it is the loose bolts issue.
 
Alpinewoodsman said:
Swivel pins it is. I could see the housing move on the lift at 6 and 12. 3 and 9 is fine- I'd done end float on the bearings all round and fixed that...
Right, park it on the flat ( hard work round here) wheel off, spare jack ready for the housing, and hope it is just loose bolts on the top pin.
Click to expand...
It won't be a loose bolt - there are four of them! There are two types of top bearing, one's a fibre plain bearing, alternative is a taper roller. If it's the fibre (Raiko) type then taking shims out doesn't really help. The purpose of that operation is to adjust the resistance to turning when you steer and you're pushing the pin down harder onto the bottom of the bush cup. When the bush's cylinder has worn you get the sideways play, and trying to stop that with pressure on the bottom won't last five minutes. New bush time. If it's a taper roller type then there is some mileage in re-shimming, but it's an indicator that the bearing has worn, and I change them anyway.
 
1985/86.. Vin plate, paperwork etc don't quite agree. Wiring is a mix of 12J and 19J. Solihull's finest really excelled themselves on build qualilty here.
 
Alpinewoodsman said:
The front wheels rock vertically if you lift them off the ground and apply some force, so if that's the diff, I've got bigger problems than I thought!
Click to expand...
Swivel bearings / pins... 100%
Get a spring balance ( fishing scales amaon cheap cheap )
Trailerfittters toolbox on you tube has an excellent how to, chris is the man!
 
You must log in or register to reply here.

Similar threads

U
Landrover freelander 1 2005 JATCO vibration on auto output cv joint
Replies
3
Views
641
GrumpyGel
GrumpyGel
M
Freelander 1 Front wheel driveshaft cv joint pulling out
Replies
5
Views
853
mdv
M
U
300TDI Gearbox or Transferbox
2
Replies
21
Views
3K
UsInWorld
U
pwood999
Freelander 1 Faint scraping noise when turning left slowly
Replies
9
Views
1K
Dippypud
Dippypud
P
Help needed please
Replies
8
Views
845
Firebobby1
Firebobby1