adrian hogg

Well-Known Member

• Oct 22, 2018

• #1

Hi People

I need to remove the centrifugal filter housing from my TD5 to helicoil the threads for dome cover. Does anyone know if there is a gasket or O ring behind it. R

 

jamesmartin

Well-Known Member

• Oct 22, 2018

• #2

o rings behind the housing,a gasket where pipe joins the sump

 

adrian hogg

Well-Known Member

• Oct 22, 2018

• #3

Cheers james

 

tom1979

Well-Known Member

Full Member

• Oct 22, 2018

• #4

While it’s off you could replace it for a good one

 

adrian hogg

Well-Known Member

• Oct 23, 2018

• #5

Wot you mean?

 

1988smithy

Well-Known Member

• Oct 23, 2018

• #6

Decent used on eBay for about £25

Better to fix things though eh?

 

bankz5152

Well-Known Member

• Oct 23, 2018

• #7

I'm still dealing with nut and bolting mine

 

adrian hogg

Well-Known Member

• Oct 23, 2018

• #8

mine may end up like that it looks awkward to remove! I wish I could get hold of the monkey who serviced it last I had to use a two foot knuckle bar to get sump plug out

 

T

triggersbroom

Active Member

• Oct 24, 2018

• #9

I screwed long bolts up from the bottom while mines was off araldited them in and use nylon nuts on top to hold cover down and cut threads down so just enough for nylon to grip

 

tom1979

Well-Known Member

Full Member

• Oct 26, 2018

• #10

adrian hogg said:

mine may end up like that it looks awkward to remove! I wish I could get hold of the monkey who serviced it last I had to use a two foot knuckle bar to get sump plug out

Click to expand...

The problem is people use the bolts to pull the lid down tight and the threads aren't strong enough for that sort of abuse. It is held on by three bolts, and is only awkward if you have air con, not impossible though.

 

Interceptorxj

Well-Known Member

• Oct 26, 2018

• #11

1988smithy said:

Decent used on eBay for about £25

Better to fix things though eh?

Click to expand...

I think a repaired helicoiled unit would be better/stronger than a used one ready to have the threads pulled out again don't you?

 

1988smithy

Well-Known Member

• Oct 26, 2018

• #12

Interceptorxj said:

I think a repaired helicoiled unit would be better/stronger than a used one ready to have the threads pulled out again don't you?

Click to expand...

Yes, maybe. More of the thinking that we don't fix much now, just replace.

1988smithy said:

Better to fix things though eh?

Click to expand...

 

tom1979

Well-Known Member

Full Member

• Oct 26, 2018

• #13

Interceptorxj said:

I think a repaired helicoiled unit would be better/stronger than a used one ready to have the threads pulled out again don't you?

Click to expand...

If people weren't such animals the threads wouldn't get pulled out in the first place

 

O

ozzyboydeano

Well-Known Member

• Oct 26, 2018

• #14

adrian hogg said:

mine may end up like that it looks awkward to remove! I wish I could get hold of the monkey who serviced it last I had to use a two foot knuckle bar to get sump plug out

Click to expand...

not hard to remove ...you will one day need to remove it for an oil cooler reason .... its only 4 bolts that holds the air con compressor and move this to one side you will see the bigger picture and then realise how easy its to remove the oil spinner

some people forget this is a serviceable item with ally threads and due the course of the thread it doesnt take much to strip due the fact they never got anti seized from factory either

 

Last edited: Oct 26, 2018

1988smithy

Well-Known Member

• Oct 26, 2018

• #15

tom1979 said:

If people weren't such animals the threads wouldn't get pulled out in the first place

Click to expand...

Mines got a nut and bolt arrangement through one of the holes. Non original and sure the bolts been bent to allow space to get the nut on

 

O

ozzyboydeano

Well-Known Member

• Oct 26, 2018

• #16

tom1979 said:

If people weren't such animals the threads wouldn't get pulled out in the first place

Click to expand...

with out the correct anti seize its normal for alloy threads to pick up very easy
all it takes is some dirt or corrosion for a thread to pick up and strip on removal

 

Interceptorxj

Well-Known Member

• Oct 26, 2018

• #17

tom1979 said:

If people weren't such animals the threads wouldn't get pulled out in the first place

Click to expand...

A shallow 6mm thread in aluminium for an item designed to be undone frequently is a bit of a cack design though really isn't it, hence why so many have failed.

 

O

ozzyboydeano

Well-Known Member

• Oct 26, 2018

• #18

adrian hogg said:

mine may end up like that it looks awkward to remove! I wish I could get hold of the monkey who serviced it last I had to use a two foot knuckle bar to get sump plug out

Click to expand...

it funny because i service my own for many years
i only give a slight nip on a short handle using 3/8 drive ratchet
and then i need a 1/2 inch drive to remove the sump plug ?
we have two different types metal reacting to different temps and this relates to distortion
using a knuckle bar on an angle doesnt help also as you loose torque more effort is needed

 

Last edited: Oct 26, 2018