pcb fault most likely a relay or bad solder joint- possibly the thermal cut out as well if it has a glass fuse holder on front is it in tact?
Sip 150 wire issues fixed - MIG Welding Forum
Is this the one?- don't spose it has a wiring diagram?
- Status
pcb fault most likely a relay or bad solder joint- possibly the thermal cut out as well if it has a glass fuse holder on front is it in tact?
Sip 150 wire issues fixed - MIG Welding Forum
Is this the one?- don't spose it has a wiring diagram?
blue beasty
Leaks an prone to bits dropping off
Yep I think so, internal layout is the same, figure its the control board as theres power out of the main on/off switch
Might have a look to see how much they are to replace when I've got a few pennies
Yep I think so, internal layout is the same, figure its the control board as theres power out of the main on/off switch
Most have gas on delay and then motor feed. Check the lance trigger wires back to machine- from the picture it looks like there is a power transistor to switch main contactor.
If you can get it to me, can look at it if you would like
blue beasty
Leaks an prone to bits dropping off
Having just seen control board prices I might well take you up on that offer! :jaw:I'll give it a good check over and see if I can rule anything out
Cheers Fan
I'll give it a good check over and see if I can rule anything out
Cheers Fan
If the board has a part number it may be possible to find a wiring diagram.
While not familiar with your model, there are either internel or external overheat protection for transformer. If they fail you will get fan on and nothing more.
Do you have a basic digital multi meter?
blue beasty
Leaks an prone to bits dropping off
Yep.....well....Pikey has
I'll pull it out from under the pile an investigate tomorrow
Yep.....well....Pikey has
I found a partial wiring diagram the power transistor bolted to heat sink is speed control for motor. Could lz courier it to me if not obvious fault.
Freddy 007...... B&W (maybe Eastnor)
BB ............Both, B&W/Eastnor
robint.............. B&W
redhand & minty .............BOTH
fanatic
Bump
200tdi ayre
ratty................B&W
Tarantula
BotswanaGuy
accy Both work depending
Sirus
110woman
Deasy.... B&W
Mandy B&W
BB ............Both, B&W/Eastnor
robint.............. B&W
redhand & minty .............BOTH
fanatic
Bump
200tdi ayre
ratty................B&W
Tarantula
BotswanaGuy
accy Both work depending
Sirus
110woman
Deasy.... B&W
Mandy B&W
Freddy 007
Gone but not forgotten
There is a pretty spreadsheet fur signing up to man/woman the club stand
Land Rover Show, Bath & West / Eastnor
There is a pretty spreadsheet fur signing up to man/woman the club stand
Land Rover Show, Bath & West / Eastnor
Yep, filled that in a couple of days ago
blue beasty
Leaks an prone to bits dropping off
We's a bit thin on the ground fer Eastnor :suspicious:
Freddy 007
Gone but not forgotten
Maybe it don't help this thread being called
'Bristol and West Land Rover Show 2013'
blue beasty
Leaks an prone to bits dropping off
chunkymunky
New Member
I'll probably be there. Just can't remember exactly when I have an event.
Freddy 007
Gone but not forgotten
What fookin eejit called it that then?
Ya just can't get the wood...
blue beasty
Leaks an prone to bits dropping off
chunkymunky
New Member
Seeing as tis in yer backyard you bastid better be
I might even camp!!! And bring some proper money.....
But no boxes this time
ratty
I'm not special I'm limited edition
I think I'll be able to come along so long as I can get there via public transport (if such a thing still exists in the west
Nearest train station is castle Carey which is about 15 mins drive from the bath and west show ground.
robint
Well-Known Member
- Status
