huddy229 said:
Steps a little too far gone, thanks though. Do you have any of the window channel seals? The rubbery felt bit the window slides in? Cheers,
Click to expand...

Do you mean the window surround? I have a couple of those. Not sure how the seal pops out though.
 
Brian S said:
The one on the thermostat housing? That should be there.
I am not sure it's got its own loom, might be part of the engine loom.

Do you mean you want a bit of the loom chopped off?
Click to expand...


Nope - its about halfway down the cylinder head to the right (looking from the front) of the rocker cover. Sits in between the rocker cover and one of the heater pipes. It has a brown 2pin connector and the wires run along the hetaer pipe (or therabouts) to the front of the engine and back to the bulkhead. Mine have run too close to the exhaust and have embrittled and the insulation has fallen apart.
 
Have had a nightmare couple of days trying to fix my landy and currently say in a&e after my best mate got hit on the head by some heavy angle iron.

Been 36 hours up the unit and had no time to consider looking at parts. :(

Next up there Saturday.
 
huddy229 said:
Steps a little too far gone, thanks though. Do you have any of the window channel seals? The rubbery felt bit the window slides in? Cheers,
Click to expand...

This is yours if you want it -
Landrover Discovery 300TDi Drivers door top frame (221332384345)
 
plastic soul said:
light guards please...how much?
Click to expand...

Having a think about those. Was gonna put them on my new one but changed my mind as they looked a pain to fit, but I have rivnuts and bolts so gonna see if its easy enough.

I liked them on my old landy so would be good to have them back on.

Will let you know.
 
Brian S said:
I have a couple of doors at home with the runners. Remind me what door again and I will check later.

:)
Click to expand...

drivers door fella, doesn't even need to be a full seal, its missing about 2 inches from the seal so whistles and blows when i'm driving haha!
 
im sure there the same, on auto's and manuals, but i could be wrong so thought id ask anyway, im after a cylinder head for a 300tdi manual, ideally with pushrods and bolts?
 
The Mad Hat Man said:
Nope - its about halfway down the cylinder head to the right (looking from the front) of the rocker cover. Sits in between the rocker cover and one of the heater pipes. It has a brown 2pin connector and the wires run along the hetaer pipe (or therabouts) to the front of the engine and back to the bulkhead. Mine have run too close to the exhaust and have embrittled and the insulation has fallen apart.
Click to expand...

if you can solder, chop it put some heat shrink over it and solder it back up
 
mastersdave2 said:
im sure there the same, on auto's and manuals, but i could be wrong so thought id ask anyway, im after a cylinder head for a 300tdi manual, ideally with pushrods and bolts?
Click to expand...

They are the same. This one is good but I will be cleaning it up and having a light skim as they always need a bit.

The last couple I've done have sold for around £200
 
You must log in or register to reply here.

Similar threads

StuRox
For Sale Land Rover Discovery 1 300tdi Front Bumper from 1998 D1
Replies
0
Views
668
StuRox
StuRox
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
Padda.116
300tdi auto disco 1 BURNING RUBBER SMELL
Replies
4
Views
299
patrickmoran
P
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
557
Padda.116
Padda.116
C
2.25 petrol ignition timing
Replies
10
Views
609
boguing
boguing