youmitegetian

youmitegetian

Active Member
so today’s job was replacing the pads on all 4 corners of the rangie, easy job so wasn’t stressing,
All replaced with no dramas, jumped in the car to pump the brakes to take up the slack as you do, pedal to the floor the first few times as expected then hard pedal, great.
After a few seconds I pressed the pedal again and it went to the floor, thought that was odd so pumped and instantly I get pedal again,
Moved it on the drive and the pedal is fine if I brake whilst moving, as soon as I’m stationary I can get the pedal to the floor on the first push.
Am I missing something or is that the way they are?
Took it for a gentle test drive and brakes worked well, but again to the floor once stationary.
 
No didn’t have any issues, all seemed to go well, can’t see any loss of fluid and once driving the pedal feels good not spongy,
 
Beyond my knowledge Datatek, sort of feels normal but don’t remember it doing that before, as I said once driving it’s as before, maybe I should bleed the brakes anyway, the fluid seems pretty murky in the reservoir
 
youmitegetian said:
Beyond my knowledge Datatek, sort of feels normal but don’t remember it doing that before, as I said once driving it’s as before, maybe I should bleed the brakes anyway, the fluid seems pretty murky in the reservoir
Click to expand...
Brake fluid should be changed every couple of years but I'd be surprised if it's straightforward on the L322, the P38 is bad enough.
 
I’ve google it and seems straight forward, start on the nsf then osf nsr then osr I thought it would be more complicated
 
Normal common or garden set up.......but you will have needed to retract the pistons, and I presume by using a g-clamp, in itself no biggy but it should be done slowly.

I'd bleed the brakes, particularly if no history.

It should be good again after that.
 
Last edited:
Used a large set of swan neck pliers but didn’t seem to be a problem, maybe it did it before, I’ll bleed it anyway just to be sure
 
This time I'd undo the nipples before squishing the pistons back.
I've had this before when fluid is ancient.
Ancient fluid guaranteed to have air in it, from converting the inherent moisture within the fluid to steam, then air pockets reside.

If you are mentally cack handed and force the piston back as if it's a time trial, then that could upset things possibly, like the fabled master cylinder seal lip reversal.
 
Last edited:
@youmitegetian related but no idea of bearing on brake pedal. Whilst you've been in at things,did you check , or have you previously checked the brake pipes? If not put it as a starred to do, soonest.
 
Yeah pipes all look good, checked the underside while it was up in the air for mot last week,
It’s the td6, sold the S/C begrudgingly,
I’m seriously looking into getting a tdv8, can’t stand the ratttling noisy td6 and fancy some more performance.
 
Yeah put it on gumtree to see what interest I had and sold it that afternoon, seems 300,000 miles didn’t put everyone off,
Regretted selling it the next time I started up the td6
 
TD6 will eat your soul, guaranteed.

Serves you right for not accepting my offer to take S/C off your hands for a small quick profit.

May your brakes be buggered completely.
 
You must log in or register to reply here.

Similar threads

Z
P38A Random braking problem-sometimes extremely hard brake pedal
Replies
19
Views
1K
Datatek
Datatek
T
Brake troubleshooting
Replies
5
Views
850
bluedog333
bluedog333
W
Brakes require pumping!
Replies
9
Views
688
Anaconda
A
S
Freelander 2 (LR2) Brake Pedal Cruise Control Switch
Replies
0
Views
249
Stevelander 2
S
N
LOF spring and pedal sticking to the floor
Replies
3
Views
1K
NdG1977
N