ant.7 · Jul 10, 2015

finally i'm getting round to rebuilding my discos inner wings, headlight boxes and body mounts. inner wing offside completely shot as pics show.

getting all the replacement bits form froggats in Macclesfield started the strip down last night.

lots to do!!!!

roger352 · Jul 10, 2015

Just think of the end result a near perfect disco

ant.7 · Jul 13, 2015

So this rebuild just got a whole new ser of problems!!

So what to do, think it a be time to sell???

Littelwill · Jul 13, 2015

Sell it and it'll just be fixed by someone else and all your hard work will be wasted.

haigy · Jul 13, 2015

Easy fix that is.trim away slowly bit at a time get a patch on it.

Chrisw8 · Jul 13, 2015

have a read of my rusty numpty thread, shows my replacement o/s inner wing.......

http://www.landyzone.co.uk/lz/f16/rust-welding-numpty-questions-253142.html

ant.7 · Jul 13, 2015

not selling it, that was just me panicking!!!

going to get the kit b inner wing and new body mount from froggatts in Macclesfield.
plate up the hole, ill attack the surrounding area tomorrow and hope not to much more is revealed??

then ill attack the nearside?

she'll be like a new un when finished. again!!!!!

ant.7 · Jul 14, 2015

Update. Not a good one!!!

Chrisw8 · Jul 14, 2015

Cut it out and plate it up.

If I can do it, anyone can !

Saltlick · Jul 14, 2015

That could be a lot worse

ant.7 · Jul 17, 2015

Quick update!

Got all the panels from Froggatts in Macclesfield yesterday, great service and panels!!

Footwell all prepared with fertan ready for welding tommorow!!

Chrisw8 · Jul 17, 2015

Impressive panel

GRATCH · Jul 17, 2015

Mmmmm........impressive.......ya can tell it's a landy repair panel.....it's already got holes in it....

Saltlick · Jul 18, 2015

Now would be a bloody good time to give the inside of the sills and that body mount some fertan treatment followed by some decent paint like bonda, then Dynax ub or dinitrol...

haigy · Jul 18, 2015

I was up frogatts the other week great fella and full of great ifeas and makes the welfing job easier with his info. And panels are great quality

ant.7 · Jul 24, 2015

Quick update.

New floor panel in. Mount and sills fertaned first as suggested!
Weldings strong but not the best looking!!
Onto the bulkhead body mount tommorow!

Retrospaceman · Jul 24, 2015

I find it really reassuring that its not just my welding that looks like that

Once cleaned up and painted no one will know.

Looking good

Saltlick · Jul 24, 2015

Don't forget to seal up the panel edges with tiger seal/sikaflex or similar. I'm undecided whether it's best to paint/prime first and then seal or the other way around..

ant.7 · Jul 24, 2015

Yep got me supply of sikaflex already to go! Paint last they guy at froggets told me!!

Saltlick said:
Don't forget to seal up the panel edges with tiger seal/sikaflex or similar. I'm undecided whether it's best to paint/prime first and then seal or the other way around..

ant.7 · Jul 24, 2015

I know it's bobbins to look at, but passes the strength test! Big hammer!!

Retrospaceman said:
I find it really reassuring that its not just my welding that looks like that
Once cleaned up and painted no one will know.

Looking good

Active Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

HUGE MEMBER

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Active Member

Similar threads