dirtyrov · Oct 13, 2012

Ok thanks. Sounds like a job which is ideally done on a ramp. I wish i still had my workshop!!

jamesmartin · Oct 13, 2012

fairly easy if you just jack up one side

dirtyrov · Oct 13, 2012

This p38 should of been left to die i think! I am regretting taking it on but i am way to far down the line. Its time the old girl realised i am not giving up and decided to be reliable!!

cheongthong · Oct 14, 2012

need a explosive view of valve block zf 4hp22

? i think i have it but have to search for it in my old computer hard disk which is not working any more :screaming_bug_eye_f:screaming_bug_eye_f:..., . it that legal to attach this on the forum here ? I PROMISE NOTHING I WILL TRY ???

jamesmartin · Oct 14, 2012

zf hp 22 covers mechanical govenor plus ecu

dirtyrov · Oct 14, 2012

cheongthong said:
need a explosive view of valve block zf 4hp22 ? i think i have it but have to search for it in my old computer hard disk which is not working any more :screaming_bug_eye_f:screaming_bug_eye_f:..., . it that legal to attach this on the forum here ? I PROMISE NOTHING I WILL TRY ???

If you have one that would be fantastic. i am thinking i may lay the car up and go for it. if i do balls it up i will have to find a second hand box. but i am quite confident, more so if i have a diagram.

cheongthong · Oct 14, 2012

:welcome2:here i have the file in the attach

:

dirtyrov · Oct 14, 2012

cheongthong said:
:welcome2:here i have the file in the attach

:

Sorry, i don't quite understand, have you attatched the file somewhere.
Computors aren't my strong point. Give me a spanner any day!

dirtyrov · Oct 14, 2012

I found this while seaarching. not the best but its something.

http://www.swedishbricks.net/700900F...lve body.gif

cheongthong · Oct 14, 2012

:doh::doh:sorry , it cannot upload the file is too big 7mb so i need to send it to you mail me,,,,,

cheongthong@gmail.com

dirtyrov · Oct 14, 2012

One email has been sent! Really appreciate it!

dirtyrov · Oct 23, 2012

Friday is D day. picked up a 2nd hand box tonight for not a lot of money. So i am going to swap the valve blocks over and hopefully i will have a fully functional gearbox!

cheongthong · Oct 25, 2012

don't forget to measure the solenoid value (the old box and the one you pickup to compare;; hear from you so

dirtyrov · Oct 25, 2012

cheongthong said:
don't forget to measure the solenoid value (the old box and the one you pickup to compare;; hear from you so

???? Sorry i don't follow! Can i not just swap the valve blocks over?

cheongthong · Oct 25, 2012

yes you can ....depend on ??? if you have the faulty solenoid of no a good working one ,, and you built it in ,,,, it better that you measure of test the solenoid before you build it in the box ,,,,

Datatek · Oct 26, 2012

Solenoids don't often fail but it's easy enough to test the coil resistance, PM me with an email address and I'll send you the test data.

dirtyrov · Oct 27, 2012

i swapped the valve block and its still the same. Must be an issue in the box itself. Worth a try though.

Datatek · Oct 27, 2012

dirtyrov said:
i swapped the valve block and its still the same. Must be an issue in the box itself. Worth a try though.

Either a clutch gone or an electrical fault. Worth looking on diagnostics before you swap the box.

dirtyrov · Oct 27, 2012

i had it plugged in but nothing showed up. i am just going to cut my losses and sell it as spares or repairs while it still drives. i have my heart set on a td5 disco (manual!)

dirtyrov · Nov 8, 2012

Sold the dam thing and bought a disco. it won! i lost.

New Member

Well-Known Member

New Member

Active Member

Well-Known Member

New Member

Active Member

New Member

New Member

Active Member

New Member

New Member

Active Member

New Member

Active Member

Well-Known Member

New Member

Well-Known Member

New Member

New Member

Similar threads