zen

Well-Known Member

Events Planner

• Mar 17, 2013

• #1

if you have..a pic please of how the headling is attached to it and where do the drain tubes go..ie in the a pillers/or not etc..


thanks

 

3.5 efi

Well-Known Member

• Mar 17, 2013

• #2

will put you one up in the morning for the tubes. sorry no headlining.

 

Dr_evil

Banned

• Mar 17, 2013

• #3

workshop manual not show how it goes together for headlining ?

 

zen

Well-Known Member

Events Planner

• Mar 17, 2013

• #4

thanks..

 

zen

Well-Known Member

Events Planner

• Mar 17, 2013

• #5

reason being installing in project and have to cut full headling to fit..and route pipes..

 

3.5 efi

Well-Known Member

• Mar 17, 2013

• #6

i have been watching.

 

3.5 efi

Well-Known Member

• Mar 17, 2013

• #7

camera's playing up but front drains to a pillars and rear drains to c pillars. hope that helps.

 

zen

Well-Known Member

Events Planner

• Mar 17, 2013

• #8

do they in the pillers (ie cant see them0 or down the sides(internally) but under the trim,and if the later where do they exit vehicle?
thanks

 

3.5 efi

Well-Known Member

• Mar 17, 2013

• #9

both inside pillars. rear exits bottom of pillar into arch area thru grommet, clipped to follow arch to terminate near rear mudflap. front exits to scuttle area and ends there, about 4" exposed.

 

zen

Well-Known Member

Events Planner

• Mar 17, 2013

• #10

ok..to clarify before i drill holes...plastic pipe enters a piller at top runs inside it so not visable and exits into area hidden by scuttle panel.

i assume it enters a piller right at the top on the side rather than in a hole drilled in the top of a piller (hidden by roof)?

and rear enters c piller and exits under car..

kool..out with drill then!

 

3.5 efi

Well-Known Member

• Mar 17, 2013

• #11

bit late but there you go, hope they help.

 

Rustystuff

Active Member

• Mar 17, 2013

• #12

zen said:

if you have..a pic please of how the headling is attached to it and where do the drain tubes go..ie in the a pillers/or not etc..


thanks

Click to expand...

I Have a 1992 with a tilt and slide sun roof... the roof lining has a lower section were the glass slides into, so I'm not sure if you can convert a standard roof lining as I don't think they have the same lowered section.
I can take a photo of the lining and sun roof if it's of any help to you..

 

zen

Well-Known Member

Events Planner

• Mar 18, 2013

• #13

thanks to all..and yes pic would be good...
pics of pipes not too late,held off drilling holes till was sure...thanks again.

 

Rustystuff

Active Member

• Mar 21, 2013

• #14

[/quote]thanks to all..and yes pic would be good...
pics of pipes not too late,held off drilling holes till was sure...thanks again.[/quote]

Have been out tonight and taken some pics.. am now uploading to 'Photo bucket' as per advice given somewhere on here ! As of yet I haven't posted any pics so this could take some time !

 

Last edited: Mar 21, 2013

Rustystuff

Active Member

• Mar 21, 2013

• #15

Pictures of my gruby tent like roof lining !!

Hadn't realised how sagy it was getting

 

Last edited: Mar 21, 2013

Rustystuff

Active Member

• Mar 21, 2013

• #16

I would have edited the previous post for this comment but it has taken long enough to get this far !!

There is a lower section directly behind the opening that allows the glass to slide back... unfortunately the sagging cloth now hides it !

[/IMG]

 

Last edited: Mar 21, 2013

zen

Well-Known Member

Events Planner

• Mar 25, 2013

• #17

ok..got it thanks...