Very nice - but are you turning it into a boat? Where are you going with this project? (!)

I get that it's not for everyone, but hey I wanted some storage in the back but didn't want a carpeted draw set like everyone else, especially as I have a canvas roof that is often rolled up,this looks a bit more fitting/different!
 
My excuse is that I'll be keeping an inflatable dinghy in mine for most of the summer. So boat-like it is.
 
Made some progress today,

Cutting in around the rear lights
image_zps2pqfscwn.jpeg


Coming together
image_zps1inqtsxd.jpeg


Top of the storage cabinet cut to size and offered up
image_zpsnch8ojn6.jpeg


image_zpslczkwwoj.jpeg


Offering up the template for the storage box lid
image_zpsj9ekpm84.jpeg


Bottom frame of the storage box in place
image_zpsfpompneh.jpeg


Forming up the sloping side and cutting out a template
image_zpsgjwl4nvi.jpeg
 
Made some progress today,

Cutting in around the rear lights
image_zps2pqfscwn.jpeg


Coming together
image_zps1inqtsxd.jpeg


Top of the storage cabinet cut to size and offered up
image_zpsnch8ojn6.jpeg


image_zpslczkwwoj.jpeg


Offering up the template for the storage box lid
image_zpsj9ekpm84.jpeg


Bottom frame of the storage box in place
image_zpsfpompneh.jpeg


Forming up the sloping side and cutting out a template
image_zpsgjwl4nvi.jpeg
That looks great. You're inspiring me to try something similar. I love it.
 
Today was fairly productive:



test fit with 5mm tile spacers where there are not rebates:

image_zpsxpjugvht.jpeg


image_zpsw3kmn6p9.jpeg


top section in place and left side board cut to shape ready for teak

image_zpsirpwackc.jpeg


image_zpsulnpywrh.jpeg


teak boarder cut and laid out

image_zpsws0tjwpz.jpeg


image_zpsgnm3bnks.jpeg


Teak for the left side offered up, centre slats yet to be trimmed down

image_zpst3c5vgdu.jpeg


image_zpsbbk8xfiq.jpeg


all trimmed to size and laid out

image_zps7mrlpl2p.jpeg


this gives a good idea of what it will look like when finished, (apart from the tile spacers and lack of caulking!)

image_zpsqkjrlidd.jpeg


next to build the box,
I’ve still not quite decided how to do this… the face of the box will be the part that opens, not sure weather or not to have it hinging from the bottom opening at the top, or hinged at the top opening at the bottom?! thoughts on this?
i figured that if it hinges from the bottom i can access it from the drivers seat, where as if it opens from the bottom i would need to be in the back to get in there!
feedback please!
 
If you want the whole face to open then it has to be hinged at the top - but hinging at the bottom is much better for all the other reasons... And that means that as it can't be full width you'll have a couple of nooks in the top corners. They could be handy, or not. Split it into two full width compartments, each with a bottom hinge - the top one having chains as on the tailgate.

Have you considered having two (admittedly short) drawers? Or a combination of the two?
 
If you want the whole face to open then it has to be hinged at the top - but hinging at the bottom is much better for all the other reasons... And that means that as it can't be full width you'll have a couple of nooks in the top corners. They could be handy, or not. Split it into two full width compartments, each with a bottom hinge - the top one having chains as on the tailgate.

Have you considered having two (admittedly short) drawers? Or a combination of the two?

now i like the idea of draws! i will certainly give that some thought!

as for hinging at the bottom, you are right i would have just the center section opening with a cubby either side, that would be the most practical, although i would have to think how to match in the teak decking so it looks like one piece, mmmm

I think ill hold off in building any more until i have worked this all out!

i need to find some nice latches too....
 
OK so it has been a while since I did an update on progress with my storage project…

i decided to stick with just a locker and not complicate things with draws!

The flooring is all cut and shaped to fit and currently dry laid, the top section of the storage unit is now in place and I have partially framed up the supports for this…

Locker lid offered up and edge trim going in…

IMG_1367_zps8wahfu9n.jpg


IMG_1356_zpsn3mwryld.jpg


Drivers side section ply cut to size and shaped to fit contours, now to cut teak to match…
IMG_1361_zpsxov9ycea.jpg


Laying out and cutting down the slats for the locker lid…
IMG_1369_zps15s2vsot.jpg


Storage lid in place, still working out weather to put alu trim in the shadow gap at the bottom of the lid or not?!
IMG_1377_zpsvp4vxub8.jpg


IMG_1373_zpsaiyluwfk.jpg


165 Degree cabinet hinges installed onto storage cabinet lid,
IMG_1380_zpsc0sygy3a.jpg


Aluminium Strip installed flush with teak to cover the edge of the marine ply,
IMG_1381_zpsgppaf9le.jpg


IMG_1377_zpsvp4vxub8.jpg


IMG_1378_zps5xhxsoml.jpg
 
Marine grade, Stainless Locking catches cut in to the storage lid; shadow gap below locker lid,
20170706_194846_resized_zpssiohsyvf.jpg


20170706_194839_resized_zps7jgiibzg.jpg


Gluing up the drivers side section… oh and my shiney new plane..
IMG_1366_zpsbobckocs.jpg


Caulking done on the first section, ready to be sanded back to flush…
20170706_184925_resized_zpsxevspcp4.jpg


Part way through the sanding off process, down to a 120 grit, soon to be 240…
20170706_185519_resized_zpskmkrvft8.jpg


Sanding completed and first layer of Tung oil applied
IMG_1385_zps2yxryddk.jpg



Lid in place along with right side panel, making small adjustments to make it fit…

20170706_185926_resized_zpsnxvdrmzo.jpg


20170706_192043_resized_zpsmictnu0w.jpg


20170706_194856_resized_zpsod3yff0f.jpg


that's it for now, hopefully more progress over the weekend...
 
Totally, completely, utterly gorgeous! I love it. Unique and you get the pleasure of telling people when they ask where you bought it from, 'No, I made it myself actually'.
 
Thanks Steve, I know, I'm looking forward to that!

Can't wait to get it caulked and oiled up...
 

Similar threads