hi, need help from any one with Nanocom box
have a 2002 2.5 p38 auto have been using the Nanocom box to get me out of trouble until by new rf ugrade unit,
had ususal rf probs and diconnected disabled alarm using nanocom box reset the eka to new number and have been using key to open ,
no real probs there occasionaly it would loc out when i opened drivers door before the central locking had kick in so i would put in eka code using the nanoocom box
today complete lock out and where i would use the namoco boxto disarm by putting in the eka code at which time doors wouyld all unlock and sngine start now it wont disarm.
have waited to key code lock out 30 mins reset still no luck
lock doors and tried reseting an new eka code which has worked before no joy there, and even after swriting the settings to the becm when i change turn off the Nanocom and then turn on again teh eka is blank as is the key fob code only code visable is the main disable code
you can change the eka using the box for a new 4 digit code tried that still no luck and the box eeps reseting to no code showing and no ey fob showing
have original key and new key from range rover
2 question to any one can help
1/ can you reset the key fob code by adding a code in the Nanocom box alarm setting (its blank at mo and will accept new numbers) if so does that then sink with the key fob, i have been able to reset and set up a new eka code before this time for some reason it wont.
2/ as i hav tinkered with alarm setting does any one know the exact alarm settings using a Nanocom box ie enable disable dm +key fob or 1hit,
lazylock? or doors = drivers or all
there is a utility in the Nanocom that offers the option to change alarm settings i want to reset them all see if that helps
should add when i first found a prob i attached Nanocom box it was blank would not power up found a 5 amp fuse had blown in the cars fuse box replaced it powered up
any help much appreciated if i figure it out today will post
have a 2002 2.5 p38 auto have been using the Nanocom box to get me out of trouble until by new rf ugrade unit,
had ususal rf probs and diconnected disabled alarm using nanocom box reset the eka to new number and have been using key to open ,
no real probs there occasionaly it would loc out when i opened drivers door before the central locking had kick in so i would put in eka code using the nanoocom box
today complete lock out and where i would use the namoco boxto disarm by putting in the eka code at which time doors wouyld all unlock and sngine start now it wont disarm.
have waited to key code lock out 30 mins reset still no luck
lock doors and tried reseting an new eka code which has worked before no joy there, and even after swriting the settings to the becm when i change turn off the Nanocom and then turn on again teh eka is blank as is the key fob code only code visable is the main disable code
you can change the eka using the box for a new 4 digit code tried that still no luck and the box eeps reseting to no code showing and no ey fob showing
have original key and new key from range rover
2 question to any one can help
1/ can you reset the key fob code by adding a code in the Nanocom box alarm setting (its blank at mo and will accept new numbers) if so does that then sink with the key fob, i have been able to reset and set up a new eka code before this time for some reason it wont.
2/ as i hav tinkered with alarm setting does any one know the exact alarm settings using a Nanocom box ie enable disable dm +key fob or 1hit,
lazylock? or doors = drivers or all
there is a utility in the Nanocom that offers the option to change alarm settings i want to reset them all see if that helps
should add when i first found a prob i attached Nanocom box it was blank would not power up found a 5 amp fuse had blown in the cars fuse box replaced it powered up
any help much appreciated if i figure it out today will post