Search results

The thought occurred to me that if I am goin to junk the old one I can drill a hole in the top and use my hand pump to suck out the fluid. Good tip about removing the headlight. I need to replace one of my front parking aid sensors and this requires headlights out, amongst other things, so...

Thanks. I will have a look on eBay. Not keen on draining the coolant and getting it out😒

As mentioned in another thread, I purchased an 08 LR3 with the 4.4 V8 and had to replace the black plastic assembly that attaches to the block. I also installed a new coolant level sensor as I had been getting Low Coolant warnings for no reason. Well I am still getting low coolant warnings but...

Seems fine in my 08. Do your Radio and CD sound good?

Tried uploading files but too large. Will see if I can find the correct schematic.

About 2 months ago a bought an 08 LR3 with 165k km to replace my 99 P38 for offroading. This car has the 4.4 V8. For a while I had been smelling coolant in the engine compartment. Monitoring coolant levels they never went down, there were no drips, and a look inside revealed nothing obvious so...

I will have another look but this section is titled "Cooling Fan".

For RHD vehicles

I have used 4x4airseals a couple times after X8R sent me and a few others with kits having the wrong size in one area. I have 3 kits of O rings and none of them have O rings that fit the valve block. Some day in the future no replacements will be available l fear.

On the P38 forum folks recommend you not try to use the air suspension system for other purposes like filling tires. The reserve air volume in the system is not large and the pump is a low volume, high pressure pump not designed to run for a long time filling up large volumes of space. D3 may be...

PowerfullUK on YouTube recently bought a RRC X fire truck in France. It has the VM engine. Their head gasket blew. Have a look at their videos.

Driving my P38 is like driving an old truck compared to my 2008 LR3. I do think the seats in the P38 are more comfortable than the LR3 even though I have premium leather. That is about the only thing better.

Any bubbles in the coolant tank with the engine running? That's another sign of head gasket failure. Doesn't always occur. Depends on where the break is.

Installed anTerrafirma swing away tire carrier on my 2008 LR3. What load of BS. These may fit an LR4 without issue but not my LR3. Problem 1: the template you use to cut a rectangular hole in the vertical face of the bumper for the latching piece to poke through is wrong. The spot marked to...

Take it for a longish drive so that it comes to full temperature. The needle should stay just to the left of straight up. Listen for odd noises and any vibrations. Try raising and lowering the air suspension. Try putting it in low range and driving a bit that way. Check for wet carpets. Could be...

I watched a YouTube video where the fellow showed how to do this. The video title was something like" 5 things you can do to stop your RR from being stolen". Turning off keyless entry was No. 1.

Well I don't offroad my L322 so it stays at normal height but there are lots of people that do jack them up and offroad them. There is a fellow on YouTube, Jay Tee, who does that.

Well if one corner is a little higher or lower than it's other side I am not going to fart around with it. I don't actually think they are different but have not measured recently.

Brother and I continued work on my 2008 RRSC changing rear rotors, pads and installed 2 rebuilt calipers as one of them was seized. Had no trouble pulling the rotors off. Did not have to back off the adjusters for the parking brake shoes. Should be good for a few years considering the low miles...

My brother and I replaced the front rotors and pads on my 2008 L322 SC. Two hours work from getting out the tools to putting them away. Pretty straightforward job except we had to use a 3 jaw puller to get one of the rotors off. Using Pagid rotors and Bosch pads. Will see how they work out...