Hi,
I am trying to fit an alarm to my 300Tdi as it's an import without factory alarm. I'm going to fit it behind the glove box.
I have the 10AS alarm ecu bu obviously it's not active.
The thing I'm struggling with is the wire colours.
I'm hoping that I'll be abl to pick wires up from...
Hi,
My new 1997 300Tdi has some issues with the Speedo...
The speed reading is way out! To get the correct mph look at the KM/h and half it!
i.e. if it says you are doing 100km/h it actually means 50mph.
Is the speedo cable driven, or electronic? Any ideas on how to fix it?
Cheers.
I have a 1993 3.5 Efi Disco with an Auto box and have a quick question to reassure me.
What engine speed is 'normal' for the box to pull away in Drive? Mine sits around 2000rpm to pull reasonably, with about the next step being 2500rpm etc.
Hope this makes sense!
Also who exactly do you...
Cheers slob,
This was my next thing to check! I just filled up the petrol tank to the brim (after re-mortgaging the house) and the starting problem I mentioned went.
Is there an easy way to check the fuel regulator? Is it possible to remove without removing the plenum and ram housing...
Now I know it's a V8 and thirsty but I estimate it's currently running between 2 and 4 mpg! It's a 3.5Ltr Auto EFi
Put it this way, you need a gas mask to stand anywhere near the exhaust. It has got LPG which comes out at about 11 mpg, but petrol is so much thirstier.
It runs fine on petrol...
Not yet Turpsy, just been worried about the MOT at the moment though. I think I may bite the bullet and do it myself on a nice weekend.
Now where did I put that hazchem suit....
I shall have a look for that one then. I seem to remember some wires sticking out of the loom when attempting to fix the heater.
Too right about Oz. I spent a year there and drove the whole country. Covered 18,000 km's in 3 months! I agree with the RWC though. Our van was on WA plates so...
So if I didn't have the Lambda's do I just unplug them and change the tune resistor, bearing in mind, they do nothing most of the time as it runs on an open loop LPG system.
BTW, where is the tune resistor? Is it the little black 'thingy' connecting to wires together sticking out of the loom...
Cheers for your reply Yella,
I was under the impression that the MOT test had to simply meet emissions requirements. The removal of a Cat (or two) contravenes the Construction & Use Regs, but to pass the MOT it isn't relevant. I await to be shot down in flames!
Hi,
My exhaust is dropping to pieces so I thought I'd use the oppurtunity to 'remove' the Cats.
I was thinking of replacing the whole system with the 3.5 Efi Non-Cat exhaust system. Two queries... Firstly, is the connection at the manifold the same? Secondly, what do I do with the Lambda...
My list of jobs just keeps getting longer! I notice when I turn the ignition the ECU light (an orange exclamation mark) turns on for a split second then goes out. Is this normal?
I'm trying to solve the excessive use of petrol other than it being a V8.
So I tried unplugging the air flow...
WooHoo!!!!! Fixed it!
After painstakingly removing half the Discos interior and tracing every possible wire I found a dodgy relay so replaced it and replaced the bodged up fusible wire under the bonnet now it's all perfect!!!
Now just need to put the dash back as it was..... and move on to...
I already have a sizeable overdraft after buying the Disco! SWMBO won't appreciate it increasing with a wedding coming up!
Do you happen to know where the relay is for the heater motor? I really do not want to remove the dash to try and trace the wiring.
I've a feeling this relay is either...
Hello again,
Firstly my heater won't work, but I have noticed when investigating that the wire from the battery (not the starter cable) seems to have been burnt somewhat at some point. There is a replacement from battery live through a 40A fuse into the passenger compartment where it seems to...
Kooga (my Discovery) wants a bit of underbody protection so I want to WaxOyl or similar.
I realise I will get very dirty lying under it with pressure washer etc.
I reckoned on it costing me about £40 - £50 in materials alone.
Is it worth paying someone to do this for me and does anyone...
Sheddy, very kind of you to host those, i'll whack them on my host for a while to ease your bandwidth!!!
Just one thing, none seem to cover the Disco I (unless it's on the third which is still downloading) does anyone have the Disco I rave???
Thanks Ormus,
Have you any suggestions on how to remove it ( I reckon I can get access to knock a screwdriver through it and try and lever it out) but I assume you have to put a new one in by giving it a good 'tap' with the universal tool (hammer) but access is severly restriced....
Hi,
I'm really hoping someone can help me!!!
Just got new Disco (well 1993!) to replace my ageing shed aka RRC. Whilst treating rear floor rust and generally tidying her up I noticed she was losing some coolant so I topped it up.
After a drive I pulled up and noticed drips of water on my...