New position at full throttle.
I also found this video that refers to the Fule pin seizure very well...(our starting point)
Thanks for all the guidance.... I know its not correct yet but I am well on the way to getting it sorted.
Great minds think a like !! Did that alerady... filed ~ 2mm mabe 3 off the idle stop. Getting difficult not to file the sounding castings in the way... might take a look at the max stop and shift the throttle a notch... at least i have my finger on the issue.... still disapointed that it was...
Humm seized throttle stops will be my issue now. To reduce tick over i need to move it a couple of turns. The other adjustment is at the min now. I was thinking of fitting a rev counter and a boost gauge... but not sure i want such mos cons spoiling the dash.
I will say it goes like a rocket...
Basically the throttle was not opening fully from what i can tell. Looking at the photo from Steve and the fact that the "fule pin" did not pop out untill the slot on the centeral screw was at 180. I loosen the armature on the throttle linkage and moved it so now fully open the slot is at 180...
Well i had a quick peek at the turbo from the air intake side. And it spins freely . No oil or dirt presennt and the bearing feel ok. Little if any play. When we assembled the engine first the turbo blew off the hose so it was working then .. I feel i need to get a gauge and check we are...
Hi Guys.. I really appreciate all the input.. i am making progress.
yesterday I did as Lynall instructed.. (only saw his post after unfortunately)
I remover the throttle linkage and got access to the blank cover and removed with an alan key.
When I got the the blank cover out I fond it had a...
Hi guys,
sorry for not getting those 4 screws off sooner but it was a bit of a "todo" getting the right screwdriver...
anyway I took off the top of the "boost compensator" chamber just now and had a peek below.
First ... I noticed a bit of oil on both sides of the black rubber diaphragm.
I...
Now... as for this engine issue.
I have ordered a manual impact driver ( arrives Friday) to shift the 4 slotted screws to get the boost diagram chamber. I can safely say the guys that refurbished the injector pump did not open it ! not sure if they would have considered part of the injector...
As requested here are a few shots as we did the build. (and I say "we" as there was a group of ~6 working on the project, I was responsible for sourcing parts and bankrolling it all)
The only reason we swooped in a 200tdi and gearbox was the handbrake and gearbox on the original was seized...
Steve Wow... that's great. thanks for sending that link.
I have a series 2a Haynes manual but nothing on the 200tdi... I had a quick look and can see the 300tdi manual I am sure the 200 is there in that link you send somewhere . I will have to have a good look. but as I understand it the...
ps... there is no smoke issue.... no black or white smoke unless I take off in the wrong gear and labour the engine than a good dose of black smoke... but normal running just fine.
Well... I took off the 6mm black pipe that goes from the turbo to the injector pump and unfortunately it looks fine. I blow through it and it is fine. also checked the short black rubber hoes it goes into at the turbo end and while it has some marking from the hose clips it also looks free of...
ok... well something is very wrong with mine. I have a 200tdi, LT77, R230 1.404 transfer box and 3.5 ratio Disco differs running on 30" tyres... but it all comes back to the engine. It has a huge Flat Spot... as you accelerate it start out fine and then stops accelerating until your foot is...
Hi. I am pretty new to this all. I have a 58 Series 2 which I put a 200tdi in, including the LT77 gearbox and R230 1.404 transfer box. Runs ok, but I am struggling with a engine strange issue.
I have had it at my local Land Rover expert, and a diesel specialist and am still no better off. The...