Hi There . Thank you for the idea but after looking into it it seems the crankshaft position sensor is more likely to cause starting problems . I have been scrambling all over the car looking for this sensor and so far I can't find it . Any advice on where I will find this sensor . Thanks

The fuel filter alongside the fuel pump under the rear wheel arch is new just two days ago . I was wondering if the clear plastic inline filter near the battery could give problems . I think it's a good idea to use a torch and a mirror to check out the pipework in front of the engine but it...

Full tank and not much of a slope at all . I did have a leaking fuel pipe from the inline filter that runs near the battery box but I simply replaced the pipe but I had this problem before that . Could the plastic inline fuel filter give any problems , I will buy a new one in the next day or two...

Sorry I don't know how to move my post . Advise please

I don't know how to move my post . Can you advise please .

2003 Freelander 1 TD 4 . After an engine change a year ago my car is sometimes difficult to start when it's been parked pointing up hill . I really don't know if the up hill parking is part of the problem but if parked flat or pointing down hill this doesn't happen . Because of this I have just...

Thanks for the advice . I am willing to try a cheaper version as long as I have the original to fall back on and in this case I could then try Specific spray cleaner to see if they work . Thanks again . Regards. Martini

That's great to hear . I'm quite new to this maintenance stuff on a Landrover and just thought because I'm retired and have plenty of time on my hands I would try and keep ours running as well as I can . Thanks for the information .

All my checks seem to be going ok so once again thanks to everyone for the info . Today I received filters in the post ;- Crankcase breather filter and the Turbo Vent filter . These are now on my car . How important is the :- MAF Sensor because I have read that it can be cleaned with special...

I did try to get everything as close to your specifications as possible and I suppose there is a little room for human error so I am pleased that you think things are ok . Thanks for this info it was interesting setting it up . Just waiting for the new propshaft support bearings now and then...

Today I did my interpretation of the owut and I would put pics on of my set up but I can't find how to do it . The whole thing was a bit rough and ready but here are my figures , 3 kilograms took 75 seconds 4 kilograms took 45 seconds 5 kilograms took 25 seconds...

Thank you for the info . Regards

Ok so as I have said the car ran nicely with no adverse noise up to this week when I replaced the propshaft . We live in the mountains of Malaga so during the summer we don't really need a 4x4 although our track and drive way are unmade so summer has no propshaft and winter we need 4x4 . I...

Same on the front and matching on the rear but that is not the point . Before I put the propshaft back on the vehicle this week everything was good . The extra noise has only happened since the propshaft was re-fitted .

All tyres are good . It's just a few days ago that I was using the car with the propshaft removed because I take it off for the summer . Whilst the propshaft is off all is great ,better fuel economy , a bit nippier and no adverse noises so this is why I think it is noise coming from propshaft...

Thank you so much for the information . Tomorrow I will try the one wheel up test . I will also check the price of propshaft support bearing because we have retired to Spain and the postage from Ebay can be expensive and the Spanish postal system quite poor . Do I need to take the propshaft off...

This site is so bloody frustrating for an old geezer like me !!! I would like some advice about my 2003 freelander . I am slowly checking everything on the car that can be done at home without a ramp etc . Just a couple of days ago I replaced the propshaft after having taken it off for the...

To complicated for me , I thought I was using the same thing I used before but obviously not . I have no idea where to go now .

Oh dear ! I am a bit of an oldy so didn't really understand how to use this site . Maybe I won't bother anymore .

Another question regarding my Freelander . After christmas this year I removed the propshaft because we really don't need 4x4 in the summer the only thing is that we got used to a little quieter running and a little better fuel economy . Now the weather is getting wetter so I have replaced the...