The silver line one I got is rubbish. I don’t want another bit of tat. Can’t warrant a fancy leccy one. Happy with manual but want one that’s not a flimsy POS. Thanks

Hi all Could I ask for a favour if someone please in that they measure the plastic edge of the d2 shifter surround where it meets the centre console? Thanks!

Anyone used? Good feedback but contemplating an expensive purchase and was interested if anyone’s had dealings…

Hi all, Any idea where I can order the above as OEM rather than it turning up in blue box? Ashcroft do HD ones but that’s overkill for me really. Just want a properly made one and not junk Thanks

Hi all, got some very odd electrical gremlins on the 300 tdi D1. I think I’m going to book the auto electrician for a visit. On starting, the wipers would jolt - other than that they won’t run. The passenger window was opening on start up. After driving it for a while I then couldn’t get it...

Say hello to Pig. A high mileage, 3 door commercial that’s been tugging around a bowser for the last few years. An almost accidental purchase. Was watching on eBay for a bit then once spoke to owner I thought I’d grab it. It won’t be a restoration by any means. It’s had most the rot issues...

One for @sierrafery if you could please mate! Ive just picked up a commercial 300tdi disco and the seller advised me the gauge had got lazy and was just reading empty (with light illuminated) clocks were all cracked up on the plastic so changed with a good spare. So far I have: Checked the...

I have one already but would love to make the pair. They have the discovery logo on with a white and green stripe on the right shoulder. Someone must have one kicking about 🙏

I’ve stripped my heated seat for the d1 and have found that the thermistor (I think it’s called this?!) may be dud. I think this as I get get continuity through the heated seat element (and it heats when connected to a battery) but I don’t get any continuity through this component, the d1 heated...

Hi all I’ll be moving my business into a newly built unit in the near future. I’m after a lift and there’s so much on the market. 2 post, 4 post, scissor etc. I’m not overly keen on pinning into the fresh concrete floor which you’d need to do for a two post. My main reason to want a lift is...

https://www.carandclassic.com/car/C1517093

Hi all, I’ll explain the points first so I don’t rattle on: 30psi 30 percent slow thinners - base and hardener mixed as per spec sheet. 15 percent advised is too thick. I’ve read elsewhere of others using 40% **** cheap gun - I used one in a set rather than my good one as my good one was a bit...

You thought this was some kind of Britain first post didn’t you!! Two questions: Could someone advise me on which colour this is please? Secondly, my primer is 3:1:1. My mixing cup has the numbers for paint and hardener but not thinner. On the thinner scale it has 5,10,15,20 etc rather than...

I assume only the 3.9 EFI came in the discovery 1? Not sure if the 3.5 did but 3.9 efi is all I’ve seen… Say you were to freshly build one, are they reliable or just prone to issues? All I know about the v8s is they can be spiky on temps? You’ll think I’m nuts but I’m considering fitting a...

Intercooler, radiators etc Anybody own any of this stuff? Not the mental money of allisports but wondering quality

I’ve had to add a number of reducers to allow my new compressor to fit to me existing filters and lines. Is there any issue with doing this?? Thanks

Good morning all, I’m after a standard head unit in good Nick with no buttons falling off. Don’t want to pay daft money for old tech but was keen to keep it original and hopefully work it with the 6 cd changer under the seat! @kevstar - don’t have one knocking about do ya?!

I know I’m not imagining this!! Someone did a nice little solution, perhaps with a 90 degree elbow for the scuttle panel drain to stop it running down the inner wing. I’m so close to a solution with a 90 degree but I can’t work out how to make flush..,, @Disco1BFG was it you???!

I think I’m clearly missing a trick. I went to use a new out the box, Clarke needle scaler. Although it has been sat in a box for years. I couldn’t get it to go?! When I take the needle attachment off, it’s clearly pushing out air. I put 90 psi through is and it doesn’t budge.. apparently it...

Does anyone have a colour chart please? Looking for non metallic interior colours that go with grey leather… thanks