Firstly whilst researching the whereabouts of the OBDII socket port for my TD4, I came across this in the passengers foot well - see pics Can anyone conform this is the OBDII socket, where to plug in a diagnostic scanner or similar? Secondly if that is the Freelander OBDII socket, are pins in...

Re: Kalkinbrer Go and peddle your rubbish elsewhere.:mil36: Why bother joining the site if that's the best answer you can offer?

Took it to LandRanger in Stockport, was told fluid could do with being changed as it looked past its best. Also could be a sticking valve in the pump? Fluid change 1st. Any tips on doing this would be welcome. Cheers

My original key has a transponder in it, so all 'high st' key cutters are out, it would have been nice as they only charge £6 or £7 to cut the fresh blade. My original key fob works as it should. I also have 2 extra spare fobs, they either need new batteries or reprogramming to my vehicle, as...

I've got one similar: http://www.landyzone.co.uk/lz/f9/freelander-td4-2002-noisy-steering-rack-full-lock-140956.html#post1427598 I don't get any lights coming on. Not found what it is yet, had a look under the footwell, there's a tie wrap around the boot, as though someones already checked...

Couldn't find any tec7 or ct1, no-one seemed to have heard of it, let alone sell it! Used some strong adhesive from B & Q instead. Especially when the garage estimated it would cost me £100 for them to do the job! Quite a messy job by all accounts, best to apply 6/7mm bead to panel & wait for...

SOLVED: I'm more inclined to change that component 1st, I initially figured it would be easier to replace everything in one go in the hydraulic clutch system, including the MSC, any garage would probably advise the same as everyone else has, to replace the MSC first, the rest to follow if the...

Re:garyrigden Did you just have the clutch replaced, or did you have the master cylinder & slave release bearing cylinder and cylinder bracket replaced at the same time too? Did you get to the bottom of it in the end? I have a the same issue as many other Freelander owners, low bite point...

Can anyone advise of any good honest Land Rover garages in the Manchester area please? I am looking to get a clutch and associated parts replaced. Thanks in advance.:D

Cheers for the tips and advice. As for the method I was advised on that didn't work for me, that method is probably more orientated for the brakes?? Had another go today, following 'Joes' tutorial again in slow time on my own. Used about 2 litres of fresh fluid this time to flush out, lots...

The master cylinder can't be goofed, as it was working before I tried to bleed the system. Trucker5774 states his pedal rises back on its own after its been pumped, whilst he is trying to bleed his system, that to me would that suggest his master slave cylinder is ok? Is this a good...

The pipeline I used was always submerged in fluid on both occasions I tried to bleed the system. I'm going to try my eezi bleed one man operation pressurised bleed kit if I can, I've used it with success on my brakes before now. If this doesn't do it, then I'm going to have to start thinking...

Anyone know of any good land rover original parts outlets - anything similar to GSF or Europarts? I came across this place: Clutch Also what is the cost of a full clutch kit,master cylinder,slave cylinder,release bearing,flywheel and anything else that may as well be replaced while the...

Great where can I get Tec7 or CT1 industrial adhesive from? Any local DIY shops or similar, how much too? Thanks.

Re: trucker5774 So the way your doing it is - two man, you open nipple then your pedal man just keeps pumping up and down with the nipple open?? I've also just tried my last suggested method that was advised to me would work. Not sure when to stop I've gone through over 1 ltr of new...

Just spoke to a mechanic friend. Here's the way to bleed apparently (I'm about to do it in 5 mins). Definitely a TWO man job. One man on the pedal. Second man on nipple. Man on pedal puts foot fully to the floor and tells man on nipple, man on nipple then OPENS the nipple (foot stays on the...

I could do with some help at the minute, I've followed the advice in the tutorial - working on my own - the tutorial doesn't say if its a one or two man job to bleed the clutch following the tutorial - so I presume its a one man job. Got to say for anyone else who's going to try this, its a...

What are the master slave cylinders and slave cylinder in the bell housing like to change over, whats the access or how much room do you have to play around with? Hopefully I won't have to change one, But I've been on eBay pricing them up. td4 master cylinder items - Get great deals on Vehicle...

So the pressure bleeding kit I have is not useful for this procedure then? Are the brakes & clutch pipeworks & reservoirs joined in any way or are they separate? I'm just wondering why they mentioned it in the haynes manual? Anyway after reading through the tutorial and its success, I just...

Here they are in pictures. They are the ones from the main bodywork, not the removable hardtop. What adhesive or mastic should I use to re-attach them properly? Something really waterproof and strong, like Araldite or similar. I was told by the last owner: Place a silicon bead around the...