Just had a new stalk 2 months ago and all well so far, am going to check switch and bulbs , hoping its bulbs however im assuming unlikely both will have gone at same time.

Series 3 headlights aren't working , full beam works , all other lights work , am thinking switch or bulb , on back of switch there are 3 wires , brown, red/black and red , has one come off ? Tried touching red and red and black but lights don't come on so does this mean it isn't the switch ...

its still with mechanic , hes old school , not a laptop in site , he also wears overalls covered in dirt and not a shirt and tie which I always find reassuring

Yeah just running a bit rough and knocking noise now , will attach noise when ava , thanks

Compression tested out ok. Battery was flat , have recharged battery and now it starts , banging isn't anything underneath , mechanic states timing is out and creating knocking , drives but noisily , mechanic revved engine to the point where I thought it was going to blow up but temp never went...

Won't start at all now , sounds similar to flat battery , mechanic thinks noise might be a coincidence and might be related to driveshaft and bad running starting may be due to ignition system which is always possible , I'll replace the whole front driveshaft to save messing about , have also...

Reilly12 I apprecaite your post is a few years old now but what was solution to the problem ? I have similar and as you know it is very annoying. thanks Neil.

Mechanics looking at in now , he thinks it head gasket , would that explain banging/shudder? , mot is next week I can't even afford that without anything else !!! Love affair with Land Rover nearly over !

Won't start at all now ! Dont suppose any of this could be starter motor related ? Checked propshaft , all seems in good condition

Just checked plugs , two nearest to bulkhead were great , other two covered in black powder , cleaned them off but still no change

Cant imagine engine is damaged as was running fine until topped up and now its worse , runs just as rough in neutral , in morning I'll look underneath and also see if bleeding radiator helps just can't understand why it has all gone wrong over one afternoon

Took 1 litre to top up oil , however was great before topping it up !

Taking children to see Santa tomorrow and have major issues with Land Rover so need some advice in order to save the day please. Land rover series 3 2.25l was running low on engine oil (light came on when breaking) so I topped it up , at same time topped up coolant ,(both in relevant fillers...

Thanks RobertP , I'll take a photo in the morning I'd be interested to know what you think

Evening , Looking at my series 3 2.25l from the front the tyres are out of line , if one wheel is pointing towards you the other one is slightly to the one side , photos to follow , any ideas? , thanks. If the track rod ends have been incorrectly measured can I open the clamp and adjust the...

ok , all sorted , took all fuses out and checked them , they all seemed good , put them back in , this solved dash lights issue , however over run issues was ongoing , messed with wires for a while and all seems good . Thankn for advice,

I was hoping that I had done the last job on the Land Rover until after Christmas however today I re routed the rear spotlight in order to have a reversing light it was a simple job and straightforward but although lights now all Work the dashboard lights come on when I break and if I remove the...

Sorted , didn't even know but I've already got halogen upgrade !! Result , there are three wires at back of halogen , blue yellow and red ? I think , the blue wire had come loose so that was a free fix , thanks for advice , spent more time thinking it over than it took to fix , however didn't...

I have a series 3. Both my headlights stopped working , I checked the fuse and had the dash off to check that the headlight wire had not come loose from the rear of the switch , it had so i reconnected it , it all seemed fine. The sidelights etc all work when I switch them on, headlights work...

Ive managed to sort this , I pointed a hairdryer at cancel arm until if softened and the re positioned it and let it set again , all done ! thanks for advice.