Run through all plugs today cleaned with electrical cleaner nothing untoward. Used cleaner on the outside of the plugs to help to free off the little clips. Visibly all looked ok, checked out speed sensors as this could explain at least two of the codes I think, one was faulty and damaged but...

Yeah your right couldn't miss this one lol, ordered two new fronts as their out, l also want to check ohm reading of a new one for reference, but do have a gut feeling this is not the only issue but fingers crossed

Found this r/h speed sensor no ohms bare wire and a join hopefully this is it l/h to check

Quick update be gentle not an auto electrician checked rear speed sensors both read 01.1 on this setting in pic both side exact same am going to clean sensors and all plugs in these areas then move onto front

Hi mate going to look at valve blocks and speed sensors and plugs today thanks will check and clean plugs behind headlights, previous owner did quite a bit of damage removing stuff maybe a wiring issue, going to put on axle stands wheels off liners out two already out ohm test on abs sensors...

Thanks mate will check it out

Will pull out the liner tomorrow check out the wiring too will run through it piece by piece

Yes their all basically communication codes will work through plugs and the obvious first, yes front valve connected, going to switch it out as still accessible nothing seems trapped so far, one strange thing since last post would like to ask you about if I may, strange light constant ticking...

Hooray it runs, but has a couple of issues to work through, steering stiff but pump turning will have a look over next day or so, but getting a few codes v0416-94. V0421-94. C1a32-01 and last but not least V0416-86 all communication issues any one have a starting point? Going to check abs plugs...

Thanks mate much appreciated

It finally happened a glow connection plug came off in my hand, am I right in thinking if I check their orientation against my 07 I can simply plug them back in to the plug? if you see what I mean, I have a spare heater plug harness could plug in and test for power?

Getting there don't have good finish like yours have brushed it on quite thick, prep is always the longest bit and every piece of dirt seems to find it's way into my eyes even with goggles Lol

Thanks mate quietly confident compressor sorted, its date code is 2013 also the new dryer balls had a larger diameter?, will run live data again after fitting valve block, just have a gut feeling, funny thing this morning it's sitting level? noticed this last night too, your paint looks great...

Hi mate just got in from work landrover seems ok no gongs or lights that's a start, gallery pressure about 70psi at tick over but fluctuation up and down, not sure but seems too quick to be possible suspect centre valve block, ordered one today, although it didn't seem to drop while at work but...

Fitted new front valve block today and zinc painted all exposed chassis on drivers side, started cleaning n/s of light surface rust removed both front air springs, fitting on 07, also removed the compressor, replaced the dryer beads and filters and fitted to my 07, was a leak from the compressor...

Yes thanks mate it's been looking underneath made me decide maybe to keep no rot few patches of rust but best I've seen, spent its life as a Chelsea tractor as new inside still has leather smell, sump to fit wiring plugs, and a few air pipes and can be fired up, still having a problem with 07...

Transfer box on, remembered to push fit the breather on top, wiring runs down lefthand top of gear/trans box then loops across top of trans and down the right side to the auxiliary heater pump and diesel filter, all seems ok, also another body earth to transfer box. Fitted props to trans box...

Fitted new balls and filters in the original compressor dryer refitted no faults suspension issues mostly done hopefully, cushion like suspension back pressure back to normal. earth on compressor was also crusty Engine back in yesterday afternoon, all went ok basically poked the gearbox...

Nice one mate, gstuart has a maintenance guide on here servicing is the key, best of luck looks gorgeous more pics?

Went out yesterday running live date pressure jumped between 50-90 psi never more, code c1130-66 air spring air supply popped up still going to change compressor for a spare I have have seen new dmk improved apparently on evilbay £150, anyone bought one? front valve block arrived may order...