I had the same problem with mine when we had the snow had the three amigos once then just the two lights on after tc and hdc, no damaged wires or loose connections,they where on and off for 3 weeks or so and never been back since so I just put it down to water/damp getting into something.Will be...

Second that, I had a lucky escape with mine,they gave up before trashing it. Just follow them posts you’ll be fine.

https://www.landyzone.co.uk/land-rover/propshaft-separation.332148/ There’s a write up that hippo has done that goes through it all and also a video grumpygel posted that me separate the propshaft from the vcu as mine were a pain to separate,but it’s not a bad job to do.

Is the maf ok?

Added some black badges and gloss black lettering to the front.Comma diesel magic/manifold clean which I done a week or so ago seems to have sorted the smoke on a cold start.still waiting for a few more bits to turn up but she’s getting there.

Wish I seen this earlier,just finished it I went forward of the windscreen not so much you can’t see it from inside I will try it out in rain see what it’s like,will just have to make some more brackets if it’s to bad .But this is the finish article for now.

Done the wiring harnesses for the pod lights and light bar ran the wires just need to make some brackets tomorrow to hold the light bar in place.Only thing I’m not to sure about is the position of the light bar,should I go across the top of the windscreen or on the bit between the windscreen and...

Finished off the trim and hardwired the footwell lights in and had a try at the Center caps.Excuse the seats it has been a work horse for the last 3 years need a good steam clean and a wet vac,failing that burning.

4 wheel alignment done after fitting the lift kit,brake calliper,drums,speaker grills and new brake lines painted,interior cleaned out and led lights fitted in the foot wells and under rear seats and ****ed about trying to tart the damaged silver trim inside.

Sorry a couple more a suggestions have you checked the crank case filter and air filter mine didn’t look like they had been changed for a while when I got it that help mine poor running and smoke or after all that work could just someone left a loose hose or split one.

After replacing all of that I’m going to assume you checked the EGR isn’t blocked or faulty ,MAF sensor is working alright ,MAP sensor isn’t blocked or faulty and the turbo is ok?

I do as well lol I check them today and there tight and I will check them again after it’s been for a run.Whats the torque spec on them?

Prop shaft back on with new bearings,engine bay de gunked as the person who fitted the egr blank didn’t fully tighten the clamp to the exhaust and some comma diesel magic added to the tank.

It was a wrestling match alright but it’s back to 4 wheel drive now without the bearing noise.The splines were rusted,but a quick clean up sorted that out.

I just didn’t fancy doing the fuel cradle on my back and the sub frame bolts looked a little suspect I would rather let someone else have one of them snap on them.Thats the first time I have used a garage in 8 years over than MOTs the last time I used one it was to rebuild the bottom end on my...

I did say to my wife “I wonder if they’ll let me help out” to which I got told to get a life, i do struggle to trust any garage.

I’m new to the area and they came recommended and been around for years but judging by the stuff that was there it seems more commercial stuff then cars but £200 quid was a good price for the fuel cradle and rear brake overhaul.but saying that I know what you mean

Looks like they just beat as the 17mm nut was right out,but back in and used a chisel and it came straight out,only problem is my bloody ring spanner is to fat for the other side,looks like I’ll have to buy more tools tomorrow . Thanks lads

Cheers I have just told them to leave it off and I’ll have ago myself,apparently they have spent 2 hours trying to separate it which didn’t fill me with confidence that they know what they’re doing.I only asked them to do it because they were taking the prop off for the fuel cradle. Cheers for...

just had a phone call from the garage my car is in to get the rear brakes,fuel cradle and vcu bearings replaced but they can’t split the propshaft.Is it more than likely they don’t know what they’re doing or can these be a pain to separate?