Hi. I dont know what type of computer is autologic but if you can get CD and cable specifically for suspensions it should help. once the car is in a hard fault even if you find the problem and replace the part, you still need to unlock the fault, it is very easy to do and only time you will...

Hi everyone and thanks for support, I got the cd and cable from UK and it did the job, after cleared the faults and open the valve block, car is ok for now. valve block "o" rings were ok, i did not have kit so I could not change them but next time I will, I cleaned them and replaced as they...

Hi, I was fixing the tailgate switch as I could not get negative from RF door switch( I have checked the CDL switch and it was not reading as it should according to following website P38 Range Rover Central Locking Door Lock Actuator CDL Switch Test Part 1-P38 Range Rover Electrical Common...

HI I have rebuild the valve block and noticed that valves were misplaced by mechanic which was causing the problem, I found the diagram and put them correctly but I am not sure about plastic cylinder covers, is there any way to know which goes were? they all connected to drive pack so I assume...

any idea of the correct order? I think actual solinoids are in correct order as I followed the diagram but I am not to sure about the covers ( black cylinders DUNLOP written on them) any advice?

little update, I checked the valve block and I found that one of the so cold mechanic has swapped the solinoid valve so I changed it and car is rising now, few problems still, yesterday left side was up and right side was down but now right side is up and left is collapsing when car is parked...

Hi Datatek, thanks for reply, I took down the valve block and followed the instruction from the website, "o" rings looking ok to me but I will still change them, I did compressor check and it is sucking the air but when i disconnected the blue hose and pressed the finger I could force to close...

Thank you very much for your help, I know I put this message more then one place but I was not sure if I would get reply, desperation :confused:, I am going to check the car today myself and diagnose the problem, wish me luck, car has not dropped in high from last night, so I am suggesting air...

Hi, I done eas unlock and following messages came up: 6.RR Signal Incorrect 4. Air Supply Fault 7. Vehicle Has Moved 2.RL Valve stuck Closed I have cleared the faults and 35mph message has gone, car started to rise but FR side was struggling and could not cope with other ones, all the sides were...

Hi, I done eas unlock and following messages came up: 6.RR Signal Incorrect 4. Air Supply Fault 7. Vehicle Has Moved 2.RL Valve stuck Closed I have cleared the faults and 35mph message has gone, car started to rise but FR side was struggling and could not cope with other ones, all the sides were...

Hi, I done eas unlock and following messages came up: 6.RR Signal Incorrect 4. Air Supply Fault 7. Vehicle Has Moved 2.RL Valve stuck Closed I have cleared the faults and 35mph message has gone, car started to rise but FR side was struggling and could not cope with other ones, all the sides...

thanks so much, i got saftwear today and will let you know what will happens, til later does any one know how heavy airsprings are?

Hi everyone, I am following your conversations as IO have a same problem but unfortunately I am in Trinidad and dont have as much choice as in London, I have ordered EAS dyagnostic CD and Cable an hoping to get it next week by DHL, than plan is to find a fault and ship the part from somewere. I...

Hi everyone, here I am in Beautiful Caribean Island and my RR p38A has EAS hard Fault with max 35mph message desplaid. little bit background information: I was told by meckanic that air dryer was leacking and I needed to change it so brought with me from London and on my jurny from airport to...

Hi everyone I have slight leak around my gearbox, someone had a look and advice me that I need to change following parts: Rear engine oil seal, transfer case front and rear seals and gasket, when I checked the parts I found following: ERR2640, FTC2979, FTC4939, I can not find gasket which...

Hi every one, brilliant job and very good pictures, I was asking my friend to do it for me and he was telling me that I need to have oil filling pump, how didi you fill yours, did u use any special pump? I have RR 2001, many thanks

Hi Kelly Its being a long time since you ve done a brilliant job, I just want to ask you if you remember that I am planing to upgrade my lights on my p38 like you did and is it posible to do myself or do I have to involve someone from garage, also if you can could you explain how did you do...

thank you in advance, you are very kind person and Now one should ever forget your kindness, could you please send me the copy on tolia5@hotmail.com I was looking for it for 2 weeks every were