• xDParis64
    xDParis64 posted the thread Freelander 1 Suspension Spring Specs in Land Rover Freelander.
    Hey all! I've been looking ALOT for some better suspension upgrades for off-road for the my '00 Freelander 1 1.8 but honestly I can find NOTHING, other than MM Lift kit which I already have and the stock suspension. I realise for the MacPherson...
    May 15, 2025
  • xDParis64
    xDParis64 reacted to GrumpyGel's post in the thread Feels like handbrake is on! FL1 1998 1.8 with Like Like.
    This is true, but it won't be 'freely' because it will also need to turn all the props, 2 diffs and another wheel. So it won't be like spinning the wheel on a 'normal' car, but it will turn quite freely.
    May 14, 2025
  • xDParis64
    xDParis64 replied to the thread Feels like handbrake is on! FL1 1998 1.8.
    Mine only happened when I also removed it replacing the drum brakes, it was not obvious until after I test drove the car and the nearside rear was smoking and my brand new shiny drum was Yellow! When manually adjusted the wheel spin freely until...
    May 14, 2025
  • xDParis64
    xDParis64 replied to the thread What have you done to your Freelander today.
    I am personally a pairs person, if one thing is broken and it has the same thing on the other side, just do both. Anything that comes in pairs or more, just do them all and if you can't do a pair, You'll find its easier to do the second one...
    May 14, 2025
  • xDParis64
    xDParis64 replied to the thread Feels like handbrake is on! FL1 1998 1.8.
    VCU is a good first check. Although a cheaper check though harder check, I would prefer to do is the auto-adjuster on the drums at the back. the spring that holds them in the right place and allows them to work without adjusting to the max each...
    • 1747237171318.png
    May 14, 2025
  • xDParis64
    xDParis64 reacted to FirebladeGuy's post in the thread Freelander 1 Coolant Hose? with Like Like.
    Ok found the time to do the job, easy with your excellent instructions, thank you. That Y piece had been 'siliconed' to the block presumably to try and stop the leak. Cleaned it all up and refitted the replacement. It still leaks!!! However, I...
    May 12, 2025
  • xDParis64
    xDParis64 reacted to Skiddy 1's post in the thread Freelander 1 handbrake switch. with Like Like.
    Found one in the Netherlands. Damen Kroes Boxtel BV. If anyone else needs one.
    May 12, 2025
  • xDParis64
    xDParis64 replied to the thread Unable to bleed brakes.
    Thank you, I plan once the master is rebuilt to fully bleed them again with a pressure bleeder on the master instead of the 2 people method. With no ABS there really shouldn't be any issues! I should imagine it is advised/required I bench bleed...
    May 10, 2025
  • xDParis64
    xDParis64 reacted to pwood999's post in the thread Unable to bleed brakes with Like Like.
    Never had any success with that methond on any car. 2 person method for me is: 1) open bleed valve & assistant pushes pedal steadily to floor & hold. 2) close bleed valve & assistant releases pedal. 3) repeat 1 & 2 until no bubbles on fluid...
    May 10, 2025
  • xDParis64
    xDParis64 reacted to Nodge68's post in the thread Unable to bleed brakes with Like Like.
    Not brake related, but I love that tattoo.
    May 10, 2025
  • xDParis64
    xDParis64 reacted to Steely_Glint's post in the thread What have you done to your Freelander today with Like Like.
    Couldn't even get the bolts undone on the wheel speed sensors, let alone clean them. Instead I disassembled the brake light switch and cleaned that which had the same result of finally making the two amigos bugger off. I also went on a side...
    May 10, 2025
  • xDParis64
    xDParis64 replied to the thread Unable to bleed brakes.
    Thank you. Have since removed the master from the car and "un-built" it 😅 Following removal it looks like the seal for the fill under the actual container was very cracked leaking and just falling to bits, some other seals were good and others...
    • 1746877298401.png
    • 1746877315324.png
    • 1746877386329.png
    • 1746877391441.png
    • 1746877513382.png
    May 10, 2025
  • xDParis64
    xDParis64 reacted to JohnM70's post in the thread WTAF?? with Like Like.
    I’m guessing someone had too much time, a vivid imagination and some odd bits kicking around…
    May 10, 2025
  • xDParis64
    xDParis64 reacted to Steely_Glint's post in the thread What have you done to your Freelander today with Like Like.
    Long time lurker, first time poster: Cleaned all the contacts on the numberplate light to make it work again - Bloody thing failed my MOT! Next job, clean all the wheel speed sensors and disks in the hope that I won't have to replace any.
    May 8, 2025
  • xDParis64
    xDParis64 replied to the thread Freelander 1 handbrake switch..
    I am in the UK, I popped the part number into google and a few pop up, I'd just recommend googling the part number and you'll find it
    May 8, 2025
  • xDParis64
    xDParis64 reacted to MarcDelonghi91's post in the thread Some diagnosis needed with Like Like.
    Cheers guys! Thanks for the input, turned out it where indeed the engine mounts that took a hit with all the roads here (unfortunately not on stock). CV joints checked and regreased. So good to continue at least with some vibrations :) Cocktails...
    May 7, 2025
  • xDParis64
    xDParis64 reacted to Loafer61's post in the thread Aluminum shavings in the sump… with Haha Haha.
    I should have left a gap between 'every' and 'one' there perhaps! 😁
    May 7, 2025
  • xDParis64
    xDParis64 replied to the thread Drinking Coolant / Head Gasket.
    Well I for once have good news, means I'm a bit of a moron, but that isn't new information. I was removing the inlet manifold today when I noticed a stud was without a nut.... I asked if someone had taken it off to a resounding... no... That's...
    • 1746461976832.png
    May 5, 2025
  • xDParis64
    xDParis64 reacted to GrumpyGel's post in the thread Unable to bleed brakes with Like Like.
    Not experienced it myself, but I think in these instances it is usually the master that has gone and needs replacing. Summat might of happened when it ran out of fluid. With no ABS, its a very simple setup and nothing really between master and...
    May 5, 2025
  • xDParis64
    xDParis64 posted the thread Unable to bleed brakes in Land Rover Freelander.
    Hey all! again! I know I have quite a few posts, I just want to keep all issues separate for tracking, I will be sure to update all posts when and if they are solved. I want to start with I know how to bleed brakes and I have done on this car...
    May 4, 2025
  • xDParis64
    xDParis64 replied to the thread Drinking Coolant / Head Gasket.
    Thank you both, really helpful! that means I am to replace the gasket and O2 Sensor coming soon, I will be sure to update here on the news, I should imagine then to replace the gasket the coolant needs to come out?
    May 4, 2025
  • xDParis64
    xDParis64 reacted to Nodge68's post in the thread Drinking Coolant / Head Gasket with Like Like.
    Yes, the rear head coolant bleed passes through the manifold, simply because the manifold is in the way. The seal of the manifold fails in time, allowing the coolant to enter cylinder No 1 while the engine is running, because the manifold is...
    May 4, 2025
  • xDParis64
    xDParis64 reacted to htr's post in the thread Drinking Coolant / Head Gasket with Like Like.
    In the plastic inlet manifold on the left hand side [as you look at the motor] there is a jiggle valve - a small diameter pipe leaves the manifold by the engine oil dipstick and connects to the coolant tank. The plastic manifold can warp... or be...
    May 4, 2025
  • xDParis64
    xDParis64 replied to the thread Drinking Coolant / Head Gasket.
    You'll have to forgive my innocence and stupidity, how does the inlet let coolant in? Does a coolant jacket / coolant galley run past/ through the inlet manifold? But even then, in my brain it would enter the combustion chamber and steam clean...
    May 3, 2025
  • xDParis64
    xDParis64 reacted to Nodge68's post in the thread Drinking Coolant / Head Gasket with Like Like.
    As Andy said, the shiny ring is the top ring visible in the gap between the piston and bore. If there's no coolant connection in the oil, then it's unlikely to be a HG. If the inlet manifold seal is allowing coolant past, then it's likely to go...
    May 3, 2025
  • xDParis64
    xDParis64 reacted to andyfreelandy's post in the thread Drinking Coolant / Head Gasket with Like Like.
    I'd say that what you can see and think are valve cut outs are the shadows or actual valves standing open looking like they overlap the bright ring. The bright ring could be the top piston ring if these are the actual valves rather than cut outs...
    May 3, 2025
  • xDParis64
    xDParis64 replied to the thread Drinking Coolant / Head Gasket.
    That's looking down at the piston through the spark plug hole, that is the piston itself. Inlet manifold can let water in? as in just water like rain and puddles or coolant? I replaced the gasket when replacing the engine so it should be okay but...
    May 3, 2025
  • xDParis64
    xDParis64 replied to the thread Drinking Coolant / Head Gasket.
    Excuse my incompetence... Shiny Fire Ring? I didn't think any of the HG sat over the piston/cylinder I take it you mean the Ring that sits on the edge of the HG:
    • 1746300348042.png
    May 3, 2025
  • xDParis64
    xDParis64 posted the thread Drinking Coolant / Head Gasket in Land Rover Freelander.
    Hey! As per usual I am having issues, at this point I work on this car for mechanical experience and not for the economic value 😂 Though recently the engine has been drinking coolant so I think it's going to need a HG so I ran a compression...
    • 1746299139618.png
    May 3, 2025
  • xDParis64
    xDParis64 replied to the thread Older F1 EML? (SOLVED).
    With no MOT i can't bring it down unfortunately, though I appreciate the offer, tried to bleed the brakes today but they won't? No air is coming out but the pedal goes to the floor and there are no leaks so super confused on that point but that's...
    May 3, 2025
Show older items