Your replacement is likely a series 2/early 2a one. If the bonnet has hinges held by 4 bolts this confirms. later bonnets have 3 hinge bolts.

Engine?

It may be your master is somewhat worn and possibly having an issue with some fluid bypassing the piston internally, this will result in a soft feel. [ there may also be some air let into system] As you are in there I recommend renewing both...

I can fix just about anything on an old Landy but when it comes to computers, laptops. I phones, Smart TV's it's well you know.:D:D:D:D Keeps my grown up kids busy sorting my cockups.

I suppose that is true enough about us old gits

Some of the jobs I missed off new rear prop , poly bushed rear trailing arms couple wheel bearing, new diesel tank , new battery box , timing belt , new water pump & p gasket, upgraded clutch spring

I found the housing here https://www.lrparts.net/219714-gear-lever-housing-for-land-rover-series-fits-1949-1984.html?gad_source=1&gbraid=0AAAAADmOzNeG3EVbOyPjpdhC4y_NbwQ6k&gclid=EAIaIQobChMIlKa249PfjAMV6ohQBh10cDLeEAQYByABEgK6uvD_BwE Will do...

Yes clean it up and just a tad of grease in the selector cups. Stick is available new, housing may be hard to find. There is a series 3 stick and housing on the flea bay. S3 stick has one bend S2 stick has two.

I know from doing a similar job some years ago that it likely will be possible but will be a mix and match of parts and you better keep a note of what was done for later repairs. As above contact Mike at Brittanica.

Probably should contact Brittanica Restorations in Canada. He could help you out, especially with sourcing of parts. All the best :)

Find a pic of a new shaft and orientate journals as per pic. You will have a 50/50 chance of getting it right or be 180 degrees out. Frankly as most of the weight is in the main section it may well be good either way.

I’ve never worried about which way round the yokes get put back on. As long as you haven’t pulled the sliding halves apart they will still be phased correctly. Happy to be corrected! 😀

I take it you mean grind off the galvanised coating around the new weld area, prior to attaching? Yes it has a reduced size at the end.

Have you made sure the calipers are in good order with all pistons free moving? As above, the TRW set is fine for a general use truck.

This is the Series section and it is about half shaft UJ's where Defenders have CV units. Ask in Defender Thread.

Only fit GKN. Did this job yesterday, aside from the new outer shafts being Britpart, and thus needing a few seconds on the grinder to make the yokes the right shape. No problems.

I think for a Series 3 with the vinyl dash the deluxe seats look better, but in series 2a backwards the simple ones are the way

Have you measure the gap(door opening) On both sides of the motor? Have you measured the doors? This will tell how much you need to make the drivers side larger

Have you tried messing about with the hinges? There might not be enough movement, then try what @dag019 suggests. But I'd at least start with the hinges.

You may not like this but to sort the door top leaning out wind window down, get both knees against at window level, grab the top of door with both hands and give a good heave to bend it in a tad. It is the sort of stuff they did at the factory...

Thanks for your reply Yeah the rear quarter was done, I’m not sure if the door shut properly before though, I’m aware of the bulkhead will be a lot of work to replace and a fair bit of money, I think I’ll have to acept the fact it’s never going...

Even a 19j model had a full set of blade fuses. Mine was a 19j but now 200tdi and it still has the standard set up. There are several relays below the fuses. For some reason I can not open your pic above.

Maybe to make them more robust?

All of your pics are of case casting numbers. The box number/suffix of a series three box is stamped on the top edge of the transfer box, [ nuts I know] Steamwally on youtube has a very good series 3 box rebuild in 3 parts. The left hand set of...

Its a pretty time consuming job to change a bulkhead as well as the cost. As the door shuts it can not be to far out. As @miktdish says pics of door closed and open and the chassis beneath the bulkhead floor may help us advise you. Fitted a new...

I just like the front look of the 1941 version.

Bantam MK2, Bantam 1941, and Bantam Austin American car on which much of the Jeep was based.

Early Bantam Jeep

Little known fact. Bantam based their original 'jeep' on Austin 7 components.

Thanks so much for responding. Yes, I have driven them. Did some green-laning in an old 90 mostly with my Brother in law. I agree they're not for everyone....it's part of why I love them. I've avoided up to now due to practical reasons & nothing...