Can I have your heater for my 90 please 🙏

Just a thought regarding vac advance Putting your foot down retards the ignition, lifting it off advances ignition to allow for leaner mixture.

Here is a very good explanation of how vacuum advance works, or doesn't. https://www.motortrend.com/how-to/1601-everything-you-wanted-to-know-about-vacuum-advance-and-ignition-timing/

I have suggested this before, but I am going to suggest it again. Pull the vacuum advance tube off the distributor, and drive it. See what difference it makes. It could get better or worse. But try driving it just as you mentioned in the three...

Can you be a bit more specific about how it feels wrong? And by the way, I had mine on a rolling road, paid lots of dosh for it, the guy did change the needle a few times and the readings he gave me were very good. But it never drove as well as...

Me camellia is going to flower soon. Buds are starting to open up slowly. Edgars excited.

Manage to get some seeds in be for the rain started lettuce, leek , carrots, cabbage, kale, inside tomatoes, sweet peppers, chilli, onion sets, shallots, so had a productive day.☺☺

File a little off the bottom third of the needle, that'll give it more fuel at full throttle :)

A little blast was enjoyed. :D It still doesn't feel right. I have put in a request for a chat to the local tuning man. :) I am sure the DWP can afford it next month. :)

Bottom, , top is attached to damper piston , bottom is at jet end You can fine tune by rubbing brasso on to remove little at a time

Is that the bottom when it is upside down? ie. the narrowest part? Cos that makes sense.

All masking tape removed oh bugger ive just looked up & ive left some round the loft hatch & some wiring trunk... For hippp ref snot the same as elephant's trunk. 🤣 🤣

Less embarrassing getting the bus. 🤣 🤣

Have you got out and under the car to see if there are any holes under there? TBH it isn't anywhere near the exhaust which runs along the nearside . We have to assume your car is right hand drive as if it isn't and you are burning your left leg...

Flipers fins same fing

Nuts have gone. That could be good news.

Rain on again, got a security light to sort I aint doing that in the rain. :oops:⚡⚡

Like you, I should have read to the end of the thread, this is sooo similar!

For boats we make a frame/mount out of angle bar (usually stainless) then sit a plastic marine battery box in the frame & bolt it on then use a webbing strap to stop the battery moving. :) Truck may need tie bar across to secure it.(instead of a...

I actually dont mind masking everything up, Most times when working on boats everything is masked up so its a few hours of nice relaxing work skiving :D Ive got a couple of big fluffy rollers not sure what they are made from. Just got the front...

Kit car builders have to do summat like this. We tend to just use a coupla long studs with hooks on the end, drill two holes in the ends of a piece of angle iron. Make holes where you want em, then pop the hooks in them, top end in the angle...

Been looking for a carrier so as I can have battery bolted to the chassis, looks like I'll have to make one Battery is 7" x 14" Can only find small expensive ones :(

Bus stop 20 yds from my gate, free on bus and goes straight into middle of town 😛 :D

Freelander broken already?? 🤣

Mornin Dull start today Gutter clearing today for a neighbour Off to town on the bus later Out for a pint tonight Have a good Saturday Stay safe all :)

Morning All. :D A Sunny start to the day at least. A bit cold though. :) No real plans for today, might take the Mini out for a blast. :) Have a great day. :D

Sorry to hear it, hope you are fully recovered. :)

You can't beat a good lambs wool roller, you see them on the tv with them sprayers seems a lot of work masking everything up , but good for fences 😐