Thank you for all you advice and guidance everyone. It turned out to be to be the pipe that goes from the radiator to the expansion tank, so all fixed! For now 😅

thats amazing! thank you! Yeah, hoping to do as much as I can, and I've been blown away by kind and helpful everyone is on here, so I'm sure I'll be asking many a question : )

Manuals here that will help apart from engine and other mods different on the lightweight http://smithies.co.nz/land_rover/ I would try not to farm out too much work as you will miss out on the learning and understanding of how bits work best...

What was it you said about "Mr Haynes" and soft face mallet use in another fred :oops: :D. J

Or try gentle persuasion with a soft faced mallet 🙄

I'm going to use the vice on my fingers each time I decide to buy something for it :)

He had a lot going on in life last we spoke. Not good stuff either. Not exactly the type to flounce is he but we all need a break from time to time. I have tried to contact him few times previously with no response Or he’s still mad at Broke...

Looks straightforward enough to DIY to me. Looking closer at it...it doesn't look unfeasible to remove the leather and use that as a template to cut and sew on new stuff. Plenty of saddlers in Shropshire would probably have the gear and skills to...

Oh…and if you did reconnect the RF unit for diagnosis, remember to reblock it again before you battery goes flat 😉

Poor psu design in the modules.

Given what you’ve learned through this experience I doubt you’ll struggle with a lockout again, aslong as your micro switches stay good (they take decades to go). Just don’t go using superlock feature, ever

Is that the Valeo influence on many P38 bits ?

It is not unknown for the BECM to get confused when the battery volts go low, often it shows as the language changing to French

Have a drill chuck and access to a lathe.... I'm just not very careful!

I think it's penny pinching, the dip stick and tube costs money, a sensor is cheaper and fashionable for marketing.

Yes 100%. I also bought a second hand binacle but programming to the car seems even more problematic than repairing the old... just trying to work out what company to go with!

Any reviews about their service ? Seems a large variation in prices between the 2 of them. £250 is not a lot for a competent company's technology & time these days .. I had the alphanumeric ribbon (no instruments) replaced on my old 5 series...

Good point, there should be 2 of them. Ah only the one

Absolutely ace 😎👍

In (what I thought was a genius move) bought it as it's ULEZ exempt! (unlike my old mazda bongo!) well. done. me! But, just realising that the money I'm probably/ excitedly going to spend on it is going to out weigh that! not. so. well. done...

Hi and welcome! Selling the kidney will probably be to pay the ULEZ. But until then, we need pics of the new Landy. We like pics… 😁

So its finally flagged a fault this morning, 3-4th gear change, town speed slow pickup and while it changes if you remove or add throttle the gearchange is successful, exactly the same symptoms and actions as it did 60k miles ago when i first got...

If you want a professional job I'd recommend Royal Steering Wheels in Aylesbury. Had a Saab 9-5 steering wheel done by them and was amazing finish. Bit of a trek but could post as an option. Or I pass by that way often and could LRFerry for you.

You have others why not measure them? Try a motorcycle panel rubber thingy, or many other car makers they all seem to use them. They sure as hell dont make them in house so most peeps will use the same...

Well we are all relieved that you are back up and actually "running" again. :D

I remove the covers on my engines as they only cover issues 😜

Well it doesn't break the bank. I've read it would be better to replace both front latches. I'm glad there is an alternative to the original land rover ones that are quite expensive. If somebody can point me in the right direction for a lhd MG...

And now you have a spare latch 😉 Thanks for posting the result. Makes big difference for the next person that comes along 👍

Well yeah on to the next repairs 😊 transfer case needs replacing

What love it again :D. J