Nodge and I have been musing about the idea of a Freelander EV. We agree it would make a great base for an EV conversion project due it's relatively light weight, the way the boot cubby could be extended to the fuel tank position and it's height...

count the threads left out from the locknut on the wastegate rod, if there are less than 12 adjust it to 12 and see then with F2 removed but if it's a noticeabe difference with fuse removed than with it in place replace the wastegate modulator...

Sounds like a plan 👍

Radius arms are wider on the disco, measure between the brackets on both axles.

I hope it's OK re re-open this tread, because I have a similar question regarding axle identification and rather than start a new thread, I thought it better to post on here. I own a 1998 Defender 90 300Tdi station wagon. It has disc brakes...

Of course, Landrover temp gauges in the dash are hopeless at actually measuring temps! 😆

Aye - several ‘projects’ over the Years, at least latest one doesn’t feature a total loss lubrication system🤣

Warm welcome Slo

Well, after a few Years in the wilderness I’ve returned to LandRover ownership - this time it’s a 2010 Discovery 4 HSE, like I don’t have enough grief in my life! It has some, errrm, issues to address - AC is fubar, brakes are interesting, the...

I had Magnecor ‘blue’ on the V8 when I bought it. It also came with 5 sets of plugs, two brand new so I think a number of plugs chops had been done! Although no misfires at the time, a couple of plugs ends felt loose to me. I then had a drama...

I always fit NGK plugs and I've never had an issue. I'd recommend not to buy Champion plugs as their quality is terrible in my experience.

Im very happy to say that she is running!!!! after all the money and time its turned out to be the black plug on the ecu hadnt been clipped in properly and on the last time i parked it up it mustve just wiggled out. when i went to test the cables...

Not the best pic, but will update profile when she is running and able to be moved for better angles.

Hi there all. It has been a while and have finally started taking things apart. The weather , time and family have been stopping me. But sun is finally out and I have some time. I took the tappet covers off and removed the plugs. Turned it by...

+1, no MAP.... only 4 sensors: MAF, FT, ECT, TPS

Here we go again :rolleyes:. Look if you couldnt sort the "small" problem on your D1 then how are you going to approach a D3 with all its tech? Buy a Jimmy and have done with it. J

Thanks Phil. The old one seemed fine, it was more the 8 contacts mounted into the cap that seemed scored and ‘secondhand’. I’ll keep an eye on it!

A new cap and rotor from SimonBBS sorted this issue, so all good there. The Disco is running nicely, but I think I’ll flush the rad (ie take it out) and refill with 50% coolant / distilled water. I’ll also take the under guard off to get at the...

The Milwaukee grease gun has a little button you push to bleed the air out nice and easy to use, it is especially useful as some of the trailers I have to grease up use three whole cartridges of grease.

I'm almost certain that here is no MAP sensor on this system. The ECU uses a full range throttle potentiometer to determine a load signal. You will need to check for flash codes. The 14CUX ECU was a primitave unit so if you have an engine light...

Hello, I received purchased a 1994 Discovery 1 with the 3.9 engine. I have quickly fallen for this vehicle and enjoy driving it. Recently my check engine light has come on. I checked the MAF sensor and now suspect the map sensor might be the...

Looking again this morning, is all of that mess only on one side of the engine? If it is, I would be putting money on a split manifold here, that is a LOT of oil and soot there so I don't think it's a recent failure, I expect it's been like it...

I have a Bambulabs X1c and it is excellent. The AMS allows it to print up to 4 colour models. Baby Groots anyone? The milwaukee box was printed too.

Arrow points to the valve.

Just a quick note of caution, do not use high power coils on this ignition system, they don't like it and will fail. I have posted on this before. Make sure you check the wiring very carefully, old corroded wires break inside the insulation...

Does the simonbbc rotor arm have the metal strip moulded in or is it riveted? I do recall another website where someone (not me!) reckoned he spent around £600 trying to sort a misfire issue which was resolved by refitting the old rotor arm....

The problem with levering or pulling the rotor arm off on the electronic dizzys is that you can disengage the auto advance/retard mechanism which is under the plate you can see when you have the dizzy cap off. You must press down on the reluctor...

Air and oil filters, new oil gone in. MAF and MAP clean, hoping to get back into the low 30s mpg on a long run again 👍🏻 Mileage: 138271

I've done a little bit of welding, but I'm not up to this. I think I might remove the interior bits myself, so I know it's done! The job is being farmed out by the MoT garage to 'their' welder bloke, so I'd imagine they'd put a bit on top of his...

What are you trying to achieve? The standard system does that doesnt it? Maybe a new thread cos I cant see why? J