6.6mm ov rain since last nite. Weren't eggspecting it. We is now back up to 1100L. Nuvva 50L and we be spillin over.

Mornin Fresher today Nothing planned, lazy Sunday Stay happy all 🙂

Morning All. :D A reasonable day here it seems, although a tad "brisk". :) Soon be Christmas eh? (158 days). Have a great day! :D

Morning all, tis very quiet here but thats about to change as the grinder is coming out :D Off to tackle the other inner wing, the rain set me back yesterday.

A crow keeps pulling my bird feeder off the stand so it can get all the spilt seeds, I'll need to cable tie it on but then its a bugger to fill. I dont want to bend the stand as it will crack all the coating. Got a squiggle coming to it, used to...

I done some polishing on my floating caravan.........& I have a galaxy A16 stupid phone.

Eye had bin int kitchen all afternoon. Planted me seeds. They is ont kitchen window sill. Made meself anuvva batch of mince and veg. Tis currently cooking int slow cooker. Had me tea at lunch time because eye can. Bin catching up on fings ont web...

Nobody likes magpies, nasty baskets.

It's a bungalow and I always leave the living room stat fully open because that's where the controller is. I keep hall, bedroom and bathroom at a medium heat and living room an kitchen nice and cosy. All pipes go into the attic and drop down into...

Eye is going to try it this year. Eye fink eye recall some make seeds that will wuk. Others dun't. Still going to havva go. Just planted anuvva 19 news seeds

Normally the down stairs hall is one ov two rads yer leave stat free wivva good flow, to allow the boilerer to dissipate heat when the rooms are up to temp. It allows the boilerer to expell heat after it switches oft, leaving the leccy pump...

Gardener.

Just spray it with water, if it looks fine then, it's the lacquer/clear coat.

yes, hallway , rad just needs a wet coat on now to finish

Where's the rad? Down stairs hall?

Might do this year Romanian guy next door says to eat em 🙂 (seeds)

Does yer pinch the seeds offit before the burds get them, to grow more sun flours?

Magpies? We have some squizzles near work that are plagued by maggies sometimes ...

My 15mm pipe bender doesn't do tight bends, only similar to the one in the picture that's why I thought 10mm pipe would be better, My brake pipe bender does 10mm so pipe should be hidden under the radiator, I'll paint the exposed pipe to match...

Not sure what that valve is there for, temp fitting? while work being done? Personally I would just take it back to the trunking and go from there neatly with 15mm. but then I have a nice pipe bender that could get from the trunking to the rad...

I finished the plastering because it wasn't straight Plumber and joiner fitted skirting and radiator on same morning working together I've since replaced the architrave and now replacing skirting and tidying plumbing up

Plasterer or plumber?

This is the wonderfull job workmen did after plastering the walls 🤔

Saw that on tinter web, but "er indoors wouldn't let me go :rolleyes:

Your right I spose I don't like compression joints on show so rather than solder a bend in I was thinking I can get a tighter bend in the micropipe so it looks neater. I also have a part roll of micro pipe in the shed and the rad needs a new...

Tidied part of me garage this morning to a (very) basic standard and binned some junk. Emptied my box of assorted drill bits yesterday and binned most of them (why I kept knackered bits I don't know). Got under me tratter bonnet this morning and...

Or cut shortern in the pipe trunking make them both run above the skirting in a neat manner and lift the Rad brackets a few inchs higher. Or just remake the 1 that used to run along the wall from inside the trunking. or just the last bit from the...

Morning all, I might get some welding done later. Off to polish a bit of my boat I may be back sooner if it starts to rain (very dull n overcast) njoy yer day zooners.

Problem is more than visual Old skirting was only 2" high and one pipe ran above and one along the wood Pipes need to be bended outwards to clear the skirting as they don't (and never have) sit nicely on the wall as they come down So either bend...