Oh mate. Commiserations on your terrible loss. We all feel for you at this sad time. 😢

Right ok peeps I went n bought a new phone yes I spent some cash please be kind....

Nope it should look like this....

No, far more old-skool NA 1275 Metro. :)

@DanClarke does yer mini engine look like this one…?

Since last time I spoke about are recently arrivals from Plu-Tow. Our moderator and founder (Peace be on him her it), has discussed the possibility of aiding new EV Evoque drivers adjust to a new area of the Landyzone forum. We welcomed the...

... I saw the MIL in hospital this PM. Not great, but brighter than last time. Kept reporting to me that there were flies all over her bed sheets and occasionally that I had flies all over my face. I kept telling her there were no flies and that...

Went to Wix this morning to collect me noo lawn sprinkler. Not had any rain for a while and ground is getting parched. Also got some noo 5mm and 6mm HSS drill bits as the ones I have been using for the last couple of decades are now scrap.

No, he's thinking about Dan's version :cool:

:rolleyes::rolleyes::rolleyes:

Wots wix ??

Dee yee nae hev Wickes north of the border? Bet there is a Scots equivalent.

So hot at the moment got some weeding done

OK, so here are the very sooty BP6ES plugs. All equally awful, no special standout cases. I shall pop some BP5ES's in (hotter plugs I think). I hope they don't do any damage, and it might burn off the carbon. :)

...brownie-points have been earned. Broken wind-sculpture welded back together and working again. :) Sausage bacon & egg brunch in a short while. Visiting the old MIL in hosp this PM. :)

Baps are boobies round here. ;)

Morning All. :D A decent nights kip but then the NDN resumed his DIY building works at 08:56. He is hammer & chiselling out masonry. The noise travels straight through the ground and up our side-wall. :( Looks like a nice day out there, coffee...

Well I would agree with you entirely. The spiel from the raffling org said it was all "souped up" with a stage 2'd head but when I got in touch with the previous owner directly before me he said it was a standard 1275 Metro lump in a Morris Mini...

Just a thought... On a non standard engine throw the reference books away :)

I have an excess of soot on all plugs. I will pull all 4 tomorrow and take a picture (hopefully a decent one) to show y'all. I have a set of BPE5 plugs I could put in to see if they stay cleaner as they run hotter, but the book does say BPE6's...

I've had more than ten Minis, gave up counting I've only ever had one that ran with light brown plugs and it burned an exhaust valve out. If you're anywhere from light grey to black without soot then it'll be fine :)

Yes indeed, it left no trace. The oil is still clear from the last change so no black trail. I did put a tell-tale there and it came away clean and dry (still is) but after tightening the cover T-bolt a bit more the seep/leak has clearly stopped.

Steel tres étrange zat you did not spot it running dahn zee sahd uv zee engine top!! 🤣 🤣

Stirrer! ;)

Henri🤣🤣

OK it is time to "fess-up". It was the rocker gasket after all. :) The LH screw-down T-Bolt was not as tight as the RH side one. One extra quarter turn (to match the resistance felt on the RH side one) and the leak stopped. So well done all...

If your oil is very clean then maybe you can only spot the bit that has run down to plughole and got dirty

Been out for a quick blatt around town in the mini. :) It always makes me smile. Oil leak sorted it seems. :) Worried a bit about over-fuelling and bore-washing the engine, but hard to say without an AFR gauge fitted. Nearly time for afternoon...

Ma hippo needs to get his dpf to 23 so he can regenerate. Few weeks ago he were on 17. Checked last nite after wuk and he were on 22.5. He dun't do many miles so it wood take several days to get to 23. We both like to go ferra drive to hexercise...

Check the edge of the door is vertical with a spirit level, in the closed position and again at 90 degrees open position. This will indicate if the hinges need adjusting.