He will need to spend some of his money and sell a few of his cars

Hard to express. Put your foot down in low RPM's and it is sluggish and sometimes we get the dreaded detonation in the inlet. Press gently and it gradually picks up and then the cycle repeats for your next gear change occasion. BUT, have it...

Can you be a bit more specific about how it feels wrong? And by the way, I had mine on a rolling road, paid lots of dosh for it, the guy did change the needle a few times and the readings he gave me were very good. But it never drove as well as...

A little blast was enjoyed. :D It still doesn't feel right. I have put in a request for a chat to the local tuning man. :) I am sure the DWP can afford it next month. :)

All masking tape removed oh bugger ive just looked up & ive left some round the loft hatch & some wiring trunk... For hippp ref snot the same as elephant's trunk. 🤣 🤣

Snot the same, flippers are limbs, fins snisant.

Less embarrassing getting the bus. 🤣 🤣

You ain't much on natrural history, stick to your wires

Like you, I should have read to the end of the thread, this is sooo similar!

Kit car builders have to do summat like this. We tend to just use a coupla long studs with hooks on the end, drill two holes in the ends of a piece of angle iron. Make holes where you want em, then pop the hooks in them, top end in the angle...

Sorry to hear that DD. do hope you are getting over it. XXX

Flipers fins same fing

Wot a waist of thyme! As if yor spellin woz a prablem. I seriously choaked at yor spellin of nozzle, Also at the fact you paintz the worls be4 the gloss!!! New neeb's bloke put up 2" of maksing tape around the woodwuk, his wimmins still...

Nuts have gone. That could be good news.

Rain on again, got a security light to sort I aint doing that in the rain. :oops:⚡⚡

For boats we make a frame/mount out of angle bar (usually stainless) then sit a plastic marine battery box in the frame & bolt it on then use a webbing strap to stop the battery moving. :) Truck may need tie bar across to secure it.(instead of a...

I actually dont mind masking everything up, Most times when working on boats everything is masked up so its a few hours of nice relaxing work skiving :D Ive got a couple of big fluffy rollers not sure what they are made from. Just got the front...

Been looking for a carrier so as I can have battery bolted to the chassis, looks like I'll have to make one Battery is 7" x 14" Can only find small expensive ones :(

Bus stop 20 yds from my gate, free on bus and goes straight into middle of town 😛 :D

Freelander broken already?? 🤣

You can't beat a good lambs wool roller, you see them on the tv with them sprayers seems a lot of work masking everything up , but good for fences 😐

Mornin Dull start today Gutter clearing today for a neighbour Off to town on the bus later Out for a pint tonight Have a good Saturday Stay safe all :)

Morning All. :D A Sunny start to the day at least. A bit cold though. :) No real plans for today, might take the Mini out for a blast. :) Have a great day. :D

Sorry to hear it, hope you are fully recovered. :)

I'm still 'ere - just about! Health problem.

Been decorating all day, my mate gave me a paint sprayer wot a pile of doodoo :mad: Spent about an hour thinned down the paint then tried it on some cardboard was like when you've had Ruby Murray n pebbled dashed the pan. 🤣🤣 Stripped the gun...

You said flippers

Yer n fish dont have flippers :p So if flippers be cut off somit its going to be a dolphin or a diver either way both will be rubbery 🤣🤣