Yes I know it's the general Land Rover section but no way is it going in "Anything goes". Short story, I want to pay more into my pension, my pension provider won't allow it so I need to change. To do this I need to employ a IFA to sort it out...

Tube out rigger might have a few years left. Chassis, if that is the worst then with time, effort, money you could probably slow the process. Fuel tank cradle is bolt on so not so important. Realistically all of our chassis are rusting away...

The Ninety has a Britpart/Allmakes/ Bearmach one for a few years and is fine. My Td5 has a Britpart one, chances are they are all the same whatever you buy.

The top of the tank is easy to see if the fuel is coming from the seal or pipe connections otherwise follow the pipes as they have a habit of rubbing through and therefore causing a leak.

Interesting, what's "a panel touching the side exit exhaust"? Welcome to the forum.

Looks a good project, make sure we get regular updates.

That's probably why I fitted a filter 🤣

The "cotton reel" type poly bushes are a pain on the rear arms, I dont see the improvement. I will find you a video. On my son's Ninety I did it all by hand with bolts and g-clamps. To be fair it was covid lock down so needed to find something to do.

Although you have the glass filter bowl on the lift pump we fitted an inline filter , cheap enough.

https://www.landyzone.co.uk/land-rover/wish-i-hadnt-started-this-job.393362/

Td5? I had to cut the head of a ring spanner and then weld a cut down socket so I could put an extension bar up past the fuel rank to undo the nut. Maybe jack the chassis up so the axle is lower, if that makes sense (probably not) You will need...

I wonder if it depends on what you want to do. If you have a base model then there will be less systems to diagnose. We don't have a Nanocom but it seems like it covers just about everything you would need.

When you count 10 motors in the group..utter madness. I go with people who I know & any bad stuff I leave or they do.

Zenith carbs are prone to warping but can be sanded flat again I do believe. Webber carb was £120 at the time so wasn't worth faffing around, sold the worn out Zenith for rebuild.

I made my own with a welder, piece of steel tube and a couple of thick bits of metal from the scrap metal yard

This place sell decent ignition parts. https://simonbbc.com/

I know, that's why I suggested a Weber.

Looking at it...being in the last third of my life and wanting to enjoy myself...what made me think trying to recover this ferrous mess was a good use of my time? Sanity check over and thank you!

I’ve been green laning since I got my first Landy in the early 90’s. I started with some friends who were members of a local off road club which was mostly into trials. We went in groups of two or three and didn’t tear up the lanes or drive off...

Having the rostyles swapped over to the wolf wheels on the ninety. 😁

Or you could spend some money here. https://www.hnjengineering.co.uk/pages/products/hnj2286su4cyl/hnj2286su4cyl.html

Welcome to the forum. I would suggest a Webber is the most affordable option. Rebuilt carbs are pretty expensive last time I looked. Don't be tempted by the Chinese Zenith, we had one and it was total rubbish. We then got a good 2nd hand Zenith...

I would replace it.

Why do people need to be told how to behave? All sorts of behaviour is available to be seen on the Internet, some just fine some not, doesn't make it an excuse. The group in the video know full well they were driving where they shouldn't and...

You can have fun and enjoy yourself without being an arse and driving illegal vehicles illegally.............. don't you think?

I used a bit of grease on the washer to hold it onto the injector when I did the 200tdi, maybe you can do the same? ^^^^ beat me to it.

Before someone else says it, it's a Ninety not a 90. It's probably/possibly/most likely a Discovery 200td engine, maybe!

Fit a new roof, well 2nd hand, look a lot better than some alloy sheet.

I hate welding on the chassis…I ain’t no welder.