P

plook

New Member
I was just driving home when there was a very violent shaking up front and it really felt like a wheel was coming off. I looked underneath and the front left wheel axle-thingy has split. I'm just about to try and find an exploded drawing of it to see if I can replace part of if it's the whole front axle. Looks like it's a whole axle to me.

Can anyone tell me how serious this is, as in, whole front axle replacement or a part. Can anyone point me towards a diagram from a manual for the area.

Help!
 

Attachments

  • DSC03284.JPG
    DSC03284.JPG
    56 KB · Views: 211
  • DSC03285.JPG
    DSC03285.JPG
    59.9 KB · Views: 209
  • DSC03287.JPG
    DSC03287.JPG
    46.7 KB · Views: 230
Fook me! I've never seen one like that before.
Start looking for a decent 2nd hand axle for sale.
 
Wow, is that a bolt on or weld on part? I do have a mig welder but currently don't have a bottle contract, but if i need to...
 
Errr...it bolts onto the panhard rod and radius arm and welds to the axle. I would try to investigate why it failed first, though.
 
I had that problem years ago. I just cut out all of th erust metal and fabricated a new bracket simillar to the one above and welded it in. Also changed all of the front bushes while i was there
 
Check the other side also, for hairline cracks etc. Preferably with a club hammer.

Probably best to do both sides at the same time.

Recently did my rear shock mounts. One had sheared apart and left the shock dangling. The other looked ok at first sight, but on closer inspection had a hairline crack in it.

I ordered new brackets for both sides anyway, lucky I did because the hairline crack snapped off completely a week later.

All good now though. It was a bit of a pain in the arse job, laying upside down under it to grind the old brackets off, but piece of **** to weld the new ones on.
 
No.

It was the rear axle :D

But also no. It would have been an easy job if not for the upside down bit really straining the neck mussles, and the difficultly getting the grinder in the right positions. All surface work on the axle casing, so couldn't really imagine the penetration of the weld would cause a problem inside the axle. Actually I didn't even consider it. I guess that those casings are pretty thick metal (although I've not had it apart).

Disconnect the battery though obviously.

And you'll need a relatively beefy welder, as the steel brackets are 5mm thick steel.
 
You dont need to drain it if the work is a t the top of the axle The level of oil will be below the drain plug which is only at part of the axle tube, If i n doubt strip it all of and wipe out the inside, Oil doesnt really burn to easily when welding, but can cause problems if the metal is thin and it seeps through the casing
 
Do I really NEED argon with a MIG welder to weld this bracket on? My contract expired a couple of years ago and until now have not needed to re-new it.
 
I don't think you need argon, my mate does a lot of fabrication on a mig with just co2, gets it from a pub for about a tenner a bottle
 
No, its mild steel. So either Argon or Argon/CO2 mix. Pretty sure the mix one is most commonly used for steel.

If you dont have a gasless welder and dont use gas, you'll find you'll get spatter and ****e all over the place and the welds will be crap and wont penetrate very well (if at all). That's my experience anyway.

If its just for this one job, you could always just get one of those little disposable bottles of gas. Welding shops will sell them. So does machine mart. Possibly even a good B and Q (if they sell welders).

Costs about 10 to 15 quid. Not sure how long they last, but might be enough for the job and you dont need an account for them.

CO2 / Argon Mix Gas Cylinder - Machine Mart
 
I didn't know about the disposable bottles, that'll do it as long as i can sort out how to attach my tap and gauges to it.

Thanks for all this help, really appreciated.
 
You must log in or register to reply here.

Similar threads

M
Spitting output housing from Transferbox
Replies
13
Views
344
tottot
tottot
D
What IS this noise ?
Replies
12
Views
947
dogdog1
D
proto57
Freelander 2 (LR2) Baffling (to me!) front Half-shaft/Axle Length Mystery! Too short, twice???
Replies
10
Views
784
Zorro587
Zorro587
L
Rotten front cross member
Replies
11
Views
1K
Anaconda
A
S
FL2 2008 TD2,2 automatic shaking and less power
Replies
13
Views
2K
Madmustang
Madmustang