M

madtrucker

Member
Hi just bought a dgital vp 37 tuning chip gone to fit and i can find the map/boost pressure sensor no prob's but trying to find the injection pump connector is harder i found what i thought it was and it was full of black wires and the instructions said that these this is the wrong side of the multi plug i can't i can't find the other side it should have 7 wires including violet, brown, black, blue, red, etc iv'e looked every where any help would helpful if you have pictures even better thanks Andy :confused:
 
madtrucker said:
sorry about that it's 2.5 diesel 1999 reg bmw engine.
Click to expand...

Do they make em for that? The pump connector is below the manifold between the FI pump and the block. Just twist and lift off. Your loom should have two plugs for this connection one that goes into socket, one that then receives plug you just took off.
 
hi i managed to get the pump connector below the manifold between the FI pump and the block off but it had 7 black to it i couldn't under might try to remove a panel from under the car to see if i can see it thanks for your help Andy
 
madtrucker said:
hi i managed to get the pump connector below the manifold between the FI pump and the block off but it had 7 black to it i couldn't under might try to remove a panel from under the car to see if i can see it thanks for your help Andy
Click to expand...

The plug should only go in one place you can't put it in wrong. Or at least you should not be able to if the thing is any good. You won't see it from under car i can assure you. The connector C1502 has seven wires. Red/Yellow pin 1. Black pin 2. Purple pin 3. Blue pin 4. Brown/Green pin 5. Grey pin 6. Red/White pin 7.
 
Last edited:
i must be looking in the wrong place then as the 1 i found came out of a small block on the right side (as looking from front of car) about 6-7 inch's into a round plug which twisted on but when i looked at wires they where all black have to have another go tomorrow thanks alot for all your help Andy
 
madtrucker said:
i must be looking in the wrong place then as the 1 i found came out of a small block on the right side (as looking from front of car) about 6-7 inch's into a round plug which twisted on but when i looked at wires they where all black have to have another go tomorrow thanks alot for all your help Andy
Click to expand...

Do the plug and socket you have on your unit match that plug? If it does that is the correct one. There is only one plug and socket like that on the entire car. The connector C1502 is under inlet manifold between injector pump and cylinder block just above where injector pipes come out of pump.. If it plugs into your new unit what colour the wires are is a sick jumbo.
 
Last edited:
it say's to connect plug to map/boost pressure sensor which is above the fuel filter then connect two wires to connection pin wires 2-violet and 3-brown or black then under that in red writing IF ALL WIRES ARE BLACK YOU ARE ON THE WRONG SIDE OF MULTIPLUG might have to contact seller thanks again for your help Andy
 
madtrucker said:
it say's to connect plug to map/boost pressure sensor which is above the fuel filter then connect two wires to connection pin wires 2-violet and 3-brown or black then under that in red writing IF ALL WIRES ARE BLACK YOU ARE ON THE WRONG SIDE OF MULTIPLUG might have to contact seller thanks again for your help Andy
Click to expand...

Yeah i know but i have told you which colour wires go to which pin. Pin numbers will be on plug just connect the wires to the black wire that corresponds to the correct coloured wire going into the socket. There is no violet wire. Pin 3 is purple. To get at them properly you will have to remove the inlet manifold.
 
Last edited:
You must log in or register to reply here.

Similar threads

MrGorsky
P38A Mystery right hand side lower dash connector....
Replies
2
Views
543
romanrob
R
JokerUK
Sport MAP/MAPT Sensors on 4.2 S/C
Replies
0
Views
608
JokerUK
JokerUK
A
P38A How to disassemble wing mirror to spray paint
Replies
8
Views
2K
AndyF07
A
Slooby
P38A 2.5 DSE Synergy 4BV3 aka 'Ronbox' - Installation Help
Replies
7
Views
1K
Slooby
Slooby
A
1992 200tdi Defender 90 wiring!
Replies
5
Views
1K
mystery
mystery