Jon Dor

Jon Dor

Well-Known Member
Is is a simple procedure to get to the seat heaters please?
Had a 2000 (W) DHSE yonks ago (2005) and the dealer had to replace both passenger and driver seat heaters under warranty.
When we got it back the difference was amazing...arse, upper thighs and back up to thoracic region toasty warm...AAAHHHHHHH!
Having a very bad back and permanent sciatica down both legs, I really need to get at least the drivers seat sorted ASAP.
Already checked out all visible fuses under the bonnet and under driver seat. Lots of oxidation carefully removed yesterday...no wonder I have a bad back!
Advice welcomed.
Thanks in advance!
 
You have to remove the seat and remove the cover. Pretty simple but not five minutes of a job. Element snaps usually mid point of lower squab just needs a bit of Teflon coated wire soldering in and heat shrink to cover joints.
 
wammers said:
You have to remove the seat and remove the cover. Pretty simple but not five minutes of a job. Element snaps usually mid point of lower squab just needs a bit of Teflon coated wire soldering in and heat shrink to cover joints.
Click to expand...
Thanks for the prompt advice Wammers.
Whilst I'm doing that, are passenger and driver seat squabs interchangeable? The drivers one has a soggy bottom (bit like the driver) and I'd like to swap if possible.
Cheers!
 
The seats have to come out then the leather squab has to come off, the seat not working is usually just a broken wire were it bends.
one of the guys on here did a write up iirc think it was @biketeacherdave or may have been @ukadamwest they also put in higher temp sensors so well toastie.
 
That's great...thanks for the prompt response and advice, brian38dse!
I'll check both of those suggested member's posts out.
 
Datatek said:
It's harder, but can be done without taking the seats out. The hog rings can be a struggle.
Click to expand...
Hog rings?
Are any special tools required to deal with them...or just a bit of cunning/brute force/common sense?
Happy with cunning/brute force, but never had much common sense...but I love my P38, so why state the obvious, eh?
 
Jon Dor said:
Hog rings?
Are any special tools required to deal with them...or just a bit of cunning/brute force/common sense?
Happy with cunning/brute force, but never had much common sense...but I love my P38, so why state the obvious, eh?
Click to expand...
Big pliers and/or a strong metal hook.
 
biketeacherdave said:
Just look up my old post you will find a how to guide, cut the hog rings off replace with cable ties
Click to expand...
Thanks for pointing me in the right direction! I've been pondering on this possibility and had come to the same conclusion. Great minds think alike, eh!
 
brianp38dse said:
The seats have to come out then the leather squab has to come off, the seat not working is usually just a broken wire were it bends.
one of the guys on here did a write up iirc think it was @biketeacherdave or may have been @ukadamwest they also put in higher temp sensors so well toastie.
Click to expand...


I have higher temp sensors.. makes a difference.. but I have to admit.. @biketeacherdave fif mine.. I made the tea and watched mostly
 
You must log in or register to reply here.

Similar threads

Goc3k
Discovery 1 SOLD 1997 300TDI manual D1, Winchester
Replies
16
Views
3K
Goc3k
Goc3k
domino
P38A Heated seats anomaly
Replies
16
Views
1K
domino
domino
Nodge68
Freelander 2 (LR2) LR trouble codes.
Replies
6
Views
30K
Keith Kernow Kernewick
Keith Kernow Kernewick
P
Range Rover P38 EKA and BeCM Lockout
Replies
6
Views
4K
Doolinjames
D
Henry_b
L322 TDV8 3.6 EGR Valve Replacement.
Replies
3
Views
21K
GerRRSportV8
G