keany

New Member
Hello everybody,

I have a 54 Defender and wanted to run this one past you as I'm quite inexperienced.

I was towing my father in laws old Mazda pickup up the yard ( slight incline) and three times as I took up the slack my Landy stalled no matter what revs I gave it. Revs died and engine stalled. As soon as it needed to make an effort it just died!

I resorted to switching to low range which did the job but not too convincingly. Wasn't a huge weight to tow. I should be able to tow 2 ton of cattle trailer with this thing!!

Could this be a problem with the clutch - haven't noticed any obvious slipping but does occasionally it gives a little "bump bump bump/ judder" when pulling away in first. Feels like it couldn't pull the skin off a rice pudding......

Thanks a lot for your help - I'm learning slowly but surely!
 
It won't be the clutch, it's an engine related problem.

Has the MAF (Mass Airflow) sensor been changed recently?
 
Hi thanks for your reply.

The MAF was replaced recently as I thought that might have been the problem. Didn't show any improvement .
 
Has it been misfiring? Check to see if there's oil in the ECU plug under the seat.

Is the turbo boosting okay?

You may need to get a diagnostic machine plugged in to see if there's a fault, and how the turbo's doing.

It could be a stuck turbo actuator if it's not boosting well.
 
Hi,

My TD5 did similar when I first got it. I noticed that I'd stalled it a couple of times ... I found it quite amusing that I could stall an engine like this. Then it became easier to do. Eventually she started to cut out on me for no apparent reason. In the end it took me 4 months of trial and error and eventually, as a second last resort, I dropped the fuel tank to fit a replacement pump and that was when I found my tank had a lot of contamination in it and the build up of "gunk" was partially blocking my pump's intake filters. That was almost two years ago and she's been going like a train ever since.

I hope this helps, I started by cleaning the oil out of the ECU plugs, then replaced the injector harness. Then the MAF sensor. Then the fuel Pressure regulator. Even changed the Crankshaft Position Sensor, which helped me discover that the wires were brittle due to the heat, I know 'coz I broke one and had to repair that too. I got right into the 10AS security ECM as well. Basically, I found lots of things that MIGHT have been the cause, but in the end it was "gunk" in the tank fouling my fuel pump. Each time I did something I thought I'd cured it, but no it still kept cutting out (when it did this, I found if I left it untouched for 36 hours she would start up again.)
 
My works TD5 cut out a few times randomly, and that was with out being under load.
Turns out it was the fuel pump. Is there a buzzing coming from the back end?
 
The judder when pulling away in first gear could be a warped pressure plate my. Brother had it on his 300 tdi also as said take your tank off an clean the pump out had that on a mates td5 after he ran out of derv. his gauge would read half full an it was empty after we cleaned it out it was like new an the gage even read normal don't forget you will need to bleed the fuel system if you take the tank off .......switch the ignition on an press the accelerator 5 or 6 times an let it pump through
 
Thanks very much for all your replies - I'll look into the points you mentioned when I'm off.

Cheers!
 
Thanks very much for all your replies - I'll look into the points you mentioned when I'm off.

Cheers!

Let us know Keany when you solve it ... too many people come on and get help and never say if he got the solution. We aint looking for gratitude, just knowledge.
 
Hi. My td5 was lacking in power whilst towing too. Turned out it was the catalitic convertor clogged up. Replaced it with a stainless straight through pipe and it pulls like a dream now! Hope you get it sorted.
Pughy.
 
Let us know Keany when you solve it ... too many people come on and get help and never say if he got the solution. We aint looking for gratitude, just knowledge.

Clanforbes - will def let you know, thanks for your help.

The problem I have is lack of confidence to check stuff out. Always worried I take something apart only to discover I should've left it well alone!! Expensive things these Landy's as you know!

Cheers!
 
Clanforbes - will def let you know, thanks for your help.

The problem I have is lack of confidence to check stuff out. Always worried I take something apart only to discover I should've left it well alone!! Expensive things these Landy's as you know!

Cheers!

Oh I know, but if you do decide to drop your tank be very very careful. Dropping the tank is easy enough, but if you let it fall too far before you disconnect the fuel lines the plastic clips on the pipes will probably break. So you need to lower it gently until you can get your hand in to disconnect the pipes (they are colour coded and just clip on, to remove them you squeeze the clips to get them off.) You can see the clips I'm on about here in my photo I think:

Off.JPG


Ignore the white pipe, that's an extra one I put in and the colours of my connectors will be different as I had to replace the broken ones.
 
Oh I know, but if you do decide to drop your tank be very very careful. Dropping the tank is easy enough, but if you let it fall too far before you disconnect the fuel lines the plastic clips on the pipes will probably break. So you need to lower it gently until you can get your hand in to disconnect the pipes (they are colour coded and just clip on, to remove them you squeeze the clips to get them off.) You can see the clips I'm on about here in my photo I think:

Off.JPG


Ignore the white pipe, that's an extra one I put in and the colours of my connectors will be different as I had to replace the broken ones.

Have you fitted a boat access panel too?
 
Have you fitted a boat access panel too?

Yeah it was an obvious choice for me as I have a boat and used to be into kayaks in quite a big way. These port covers have been used for a multitude of purposes by me and many others. Perfect for the job, but I shoulda gone with a black one.
 
Yeah it was an obvious choice for me as I have a boat and used to be into kayaks in quite a big way. These port covers have been used for a multitude of purposes by me and many others. Perfect for the job, but I shoulda gone with a black one.

Hahaha that's what I thought too:D:D:D
 

Similar threads