listerdiesel

Well-Known Member
Events Planner
I'll make this a thread rather than just a couple of pictures.

Our youngest son, Philip has had this trailer for 3-4 years without getting stuck into it, but things are moving now, hopefully, the body is off and he pressure washed the chassis yesterday.

The plan is to extend the chassis by 600mm at each end and build a camper body onto it.

I'll post some pictures as we go along, bodywork will be Aalco extrusions again, similar to the 6-wheel drawbar trailer.

Sankey15.jpg


Sankey16.jpg


Peter
 
'Trailer 3/4 Ton' is the designation, so not a lot really, but it is designed to carry that across country. For what he needs, it's more than enough.

Got a fair bit done this afternoon, the rear chassis was cut off and 750mm of extension welded in. Note that Philip always wears goggles when grinding or cutting, he caught a hot bit of steel in his eye just before we were leaving for Holland a few years ago and has worn them on these jobs ever since. Lesson learnt!

The pictures aren't posed, you can see the sparks round his feet if you look.

Sankey31.jpg


Sankey18.jpg


Sankey20.jpg


Sankey21.jpg


Sankey22.jpg


Sankey23.jpg


Sankey24.jpg


Sankey25.jpg


Sankey26.jpg


Sankey27.jpg


Sankey28.jpg


Sankey29.jpg


Sankey30.jpg


Got the reinforcing plates to go over the welds yet.

Going to the local metal scrap yard to see if we can get some more 100X50 box section, the piece we ordered hasn't arrived.

Peter
 
Last edited:
nice job so far, pretty neat looking welds, I would definitely wear goggles for grinding, I should imagine one of those sparks in the eye is extremely painful.
 
ah interesting. i'm thinking of keeping mine pretty much standard army kitchen body, but sticking a roof tent on the top.

i always wear goggles and gloves (usually) too.

i had a disc explode on me before.. not fun.

btw what's the big leccy boxes in the garage?
 
When you do the front extension , I would take the opportunity to extend the front further than the rear as it is quite easy to end up rear heavy with these trailers, not a good thing :(
 
The 'leccy boxes' are a battery tester system for testing 110V Nicad battery rafts on EMU's. It isn't a garage, that's the roller shutter entrance at the factory.

http://www.prepair.co.uk/Tester.htm

Regarding weight balance/distribution, we've started the front extension today having picked up a decent bit of 100X50 at our local metal scrap yard, and in fact the rear has the longer extension at 750mm than the front with 600mm.

There will be an underslung LPG vapour tank and water tanks so we'll be able to balance it up by positioning those items.

Rain stopped play unfortunately, may get back up there later and carry on.

Sankey32.jpg


Sankey33.jpg


Sankey34.jpg


Just started raining as I took the pictures. More involved bracing needed at the front to strengthen the drawbar.

Peter
 
Last edited:
Looks like an interesting project. Is that a rather rusty series chassis I see leaning against the wall too?
 
Looks like an interesting project. Is that a rather rusty series chassis I see leaning against the wall too?

Yes, but I think it is probably terminally rusty, even Philip's skills aren't going to bring that back to life :D:D

Peter
 
Today's efforts.

We got the front A-frame re-connected, made up to two perimeter frames for the front floor and got the A-frame cross-beam welded in.

Going to temporarily rig up the lights and get it weighed in the morning. Length is about 4 metres now.

Sankey35.jpg


Sankey36.jpg


Sankey37.jpg


Sankey38.jpg


Sankey39.jpg


Sankey40.jpg


Sankey41.jpg


Sankey42.jpg


Sankey43.jpg


Sankey44.jpg


Peter
 
Last edited:
Nice work as always Peter.

How's the Bus conversion coming along? Haven't seen an update of that one lately.
 
We are at the stage of taking out the old windows, plating over the old bodywork with 16g dural and then fitting new windows:

VarioWindowIn2.jpg


The roof lining is finished:

VarioCupboard20.jpg


VarioSkylight1.jpg


Solar panels are wired up and the controllers running:

VarioSolar40.jpg


Just back from holidays in France and Holland with the big trailer, got to get back onto that now. Mercedes blog link in my signature.

Peter
 
Last edited:
Fantastic project. I have considered something similar but on a considerably lighter scale.
Whilst studying the excellent photographs in bed this morning I cant help asking a few questions. What led to the decision to bisect the drawbar beams within their angle rather directly from the crossbeam. And have you any more close ups of the welding. Possibly with a slightly squoze tube of copper grease in shot and some strongly drawn finger marks pulled manly across the bare steel.

;)
 
We wanted to leave the junction between the drawbar A-frame and the first cross-member alone, and with the joint out in the open as it were we can plate over the welds more easily. The A-frame members go back to the second cross-member.

I didn't take any more weld pictures, but will do as the job goes along.

Biggest problem today was a stiff breeze which caused the shielding gas to blow away from the weld, but we got round it by holding a big sheet of plastic around Philip as he was welding.

Peter
 

Similar threads