H

Henrik97

Active Member
Hi all,
My key fob is acting up. The lock button works fine, but the unlock button is intermittent at best. Replacing batteries did not help. If I stand next to the car, furiously pushing the unlock button dozens of times it will finally unlock, but I can see the day looming when it doesn't work at all. I suspect that the actual switch has gone bad - have any of you attempted surgery on one of these units? A new fob is outrageously expensive, so I hope it can be repaired, either by me or someone you recommend.

Cheers!
Henrik
 
Have stripped a few and replaced cases. And a few solder repairs. I suppose the switch could be changed with a bit of deft soldering. Plenty of micro switches on the bay of E. If you are cutting the case open DO NOT cut near the LED. Break that bit away. I cut from key ring end towards battery position then prize the case open. You will need a new case. But take care you retain the small metal clip for battery contact that fits in the lid. Most new cases you get don't have this included. You will also have to remove the key blade and fit it to the new fobs pivot.
 
Thanks Wammers, I'll give it a whirl. Hopefully, I'll be able to build one working fob from my two duff ones.

H.
 
Henrik97 said:
Thanks Wammers, I'll give it a whirl. Hopefully, I'll be able to build one working fob from my two duff ones.

H.
Click to expand...

If you cock it up and end up with neither working just disable EKA and immobiliser in BECM and use the key until you get a working one.
 
Sorted!
I'm bleeding from three fingers after prying my two fobs apart - they are seriously well stuck together - but I now have one that works. I swapped one of the switches over and now all is well. Very fiddly soldering, but it can be done after a beer or two. New case is on order, but the old one will do for now. I just saved over £400 for a new key, so I believe I have earned another beer...:)

Thanks for your help!

Henrik
 
Henrik97 said:
Sorted!
Very fiddly soldering, but it can be done after a beer or two. New case is on order, but the old one will do for now.
Henrik
Click to expand...

I recommend the BIg Job from St. Austell brewery. Drink straight from the fridge n this hot and muggy weather. Perfect.

Henrik97 said:
I just saved over £400 for a new key, so I believe I have earned another beer...:)
Henrik
Click to expand...

New key from the Main Stealer should be about £165 (and that includes the dreaded VAT). Who quoted £400?
 
I'm in Norway, so nothing from St. Austel brewery and very expensive parts (and beer). It would be next to impossible to get a new key for a Norwegian car through a UK dealer. All else I get from the UK at half the price or less.
BTW, the new case in question is an empty key fob shell, not a case of beer..
 
Henrik97 said:
I'm in Norway, so nothing from St. Austel brewery and very expensive parts (and beer). It would be next to impossible to get a new key for a Norwegian car through a UK dealer. All else I get from the UK at half the price or less.
BTW, the new case in question is an empty key fob shell, not a case of beer..
Click to expand...

If I were to go with the VIN number surely I'd be able to get one? And then post it, perhaps? They did ask for ID for mine but when I turned up they never bothered with it.
 
I think the keys come from Germany. Hoff, perhaps? May be possible to contact directly? £400 is just robbery.
 
You must log in or register to reply here.

Similar threads

MrGorsky
P38A Occasional "Engine Disabled Press Remote" message on dash.
Replies
19
Views
1K
Datatek
Datatek
DollyBird
Extra fob battery connector?
Replies
1
Views
300
doriz
doriz
Rubberknees
P38 key fob
Replies
14
Views
2K
Rubberknees
Rubberknees
B
Not all doors unlock with key fob on FL2 ?
Replies
6
Views
993
Nodge68
Nodge68
marjon
L322 Key fob case replacement.
Replies
5
Views
551
marjon
marjon