AndyF07

Active Member
Hi,

I've searched forums, internet and Rave to the best of my ability and can't find anything so am hoping the wisdom of the forum can help.

I am replacing both my damaged wing mirrors ( the whole assembly not just the glass ) and as I couldn't find any in the right colour have got a couple of second hand ones which I will spray. I would like to do a proper job but can't see how to remove the mirror casing (i.e the coloured part) from the black 'bracket' so I can spray the casing properly. Can anyone offer any advice before I start dismantling ?

On a side note there is a loose connector inside both connected to the mirror with a green and a black wire but there is no corresponding connector. Am I right in assuming these are for heating the mirror and have been retrofitted into a case without the functionality ?

Thanks for any advice. Cheers.
 
Hi,

I've searched forums, internet and Rave to the best of my ability and can't find anything so am hoping the wisdom of the forum can help.

I am replacing both my damaged wing mirrors ( the whole assembly not just the glass ) and as I couldn't find any in the right colour have got a couple of second hand ones which I will spray. I would like to do a proper job but can't see how to remove the mirror casing (i.e the coloured part) from the black 'bracket' so I can spray the casing properly. Can anyone offer any advice before I start dismantling ?

On a side note there is a loose connector inside both connected to the mirror with a green and a black wire but there is no corresponding connector. Am I right in assuming these are for heating the mirror and have been retrofitted into a case without the functionality ?

Thanks for any advice. Cheers.


In regards to wiring in theory there would be 4 wires, two would be heated mirror which I believe all had as standard though I could be wrong and the other two which likely would be the green and black would be for the electrocromatic function where when the rearview mirror darkens when somebodys lights behind you hit it in theory the wing mirrors do too. I believe the glass that can do that though costs an absolute bomb so people just replace with standard heated mirrors when needed.
 
There are two types of mirrors 6pin connector and 10pin, all are heated and electric but the 10pin works with the preset seat positions as to which fob opens the door,cant help with removing the plastic cover, it may be a case of masking up.
 
Housing & bracket only show as complete assembly on Lrcat.
I've painted a lot of wing mirrors on a lot of cars (professionally) & I've just masked up as required.
Don't forget to remove the tape carefully from the non-painted bits after the last coat before it dries.
 
Housing & bracket only show as complete assembly on Lrcat.
I've painted a lot of wing mirrors on a lot of cars (professionally) & I've just masked up as required.
Don't forget to remove the tape carefully from the non-painted bits after the last coat before it dries.

Thanks @Ratae. I suspected it was but just wanted to check. Cheers for the tip as well as I haven't done much in the way of painting and spraying !
 
In regards to wiring in theory there would be 4 wires, two would be heated mirror which I believe all had as standard though I could be wrong and the other two which likely would be the green and black would be for the electrocromatic function where when the rearview mirror darkens when somebodys lights behind you hit it in theory the wing mirrors do too. I believe the glass that can do that though costs an absolute bomb so people just replace with standard heated mirrors when needed.

Thanks @Khemitude. That makes sense.
 
Last edited:
You can separate the bits. But it's a right faff...you need to depin the electrical connector. And remove a spring loaded star washer IIRC
 
I have done this to 2 pairs of mirrors, it is a faff but can be done. I haven't needed to remove the star clip but when undoing the adjustment motor where the mirror clips in there is a slot. I have clipped the end off of this which allows it to pass through the body otherwise you will be there forever!
 
You can separate the bits. But it's a right faff...you need to depin the electrical connector. And remove a spring loaded star washer IIRC

I have done this to 2 pairs of mirrors, it is a faff but can be done. I haven't needed to remove the star clip but when undoing the adjustment motor where the mirror clips in there is a slot. I have clipped the end off of this which allows it to pass through the body otherwise you will be there forever!

Thanks guys. In the end I thought it was too much of a faff as you both say so masked everything up. Pleased with how they’ve turned out, a lot smarter than the two smashed ones they replaced !
 

Similar threads