S

Stu63

Member
P38 in particular, mechanically I'm pretty much ok but strength and health wise debatable. Worked on many cars over the years nothing major apart from a 6sp gearbox a few months ago on a punto and vowed I wouldn't doo it again.
So how easy or hard is it work on these ie brakes, wishbone/ control arms, ball joints (compared to cars), drop links ect.
Obviously parts are bigger and heavier but I'm wary very wary.
 
Pretty simple/easy really. Some stuff is heavy or awkward, like getting the transmission out if you are on the ground, but really ….. it is a pretty basic truck. Something like front ball joints can be a pain, but if you have the right tools, pretty easy.

Sound mechanical knowledge of 1970s to 1990s technology, and a reasonable grounding (pardon the pun) in electrics and there isn’t much else to think about. There is plenty of help in places like theirs and a couple of other forums.

.
 
Electrical diagnostics is the most frustrating bit about them, everything else is pretty reasonable to do if you have the tools required be prepared to end up covered in oil no matter what job you do as it is a Land rover after all
 
One of the easiest cars I've ever worked on. Mainly because there's usually quite a lot of room to get at stuff.
 
Stu63 said:
P38 in particular, mechanically I'm pretty much ok but strength and health wise debatable. Worked on many cars over the years nothing major apart from a 6sp gearbox a few months ago on a punto and vowed I wouldn't doo it again.
So how easy or hard is it work on these ie brakes, wishbone/ control arms, ball joints (compared to cars), drop links ect.
Obviously parts are bigger and heavier but I'm wary very wary.
Click to expand...
As someone who can no longer spanner, I find the L322 as follows:
I have assisted my old, friendly, general indy, on brakes, calipers and other smaller 'grunt' work on mine , back in the early days. These things are still done by my local, truck, mechanic.
The bigger 'grunt' work I left to him and his lad. Still a general indy.Again now being done by local, truck, mechanic.
Certain 'grunt' work such as propshaft, was done by specialised indy.
Electrickery, in the main, I have left, wisely, to specialised indy. Mainly because of diagnostics needed.
In summary, if you have the space, tools, knowhow, willing helper, and heal quickly ,most can be done.
Not sure if this was what you were after. :)
 
Tenebreaux said:
LOL. No, thank f*ck. I've read the horror stories.
Click to expand...
It's quite an interesting job I bought my p38 with a leaky diesel pump for 700 quid and done that myself for 35 quid on a genuine seal kit then about a week later my carpet was drenched long story short I would rather dismantle the pump and reassemble it again several times over than do my heater matrix again lol
 
kermit_rr said:
Local garage refused to do my front radius arm bushes
Click to expand...
They've obviously tried to replace them before,a right bastid without the proper tool.;) I've done it once using jubilee clips to squeeze the bush but last time I used poly bushes and never noticed any ride difference,used only to replace the hockey stick bushes I must add.
 
tomcat59alan said:
They've obviously tried to replace them before,a right bastid without the proper tool.;) I've done it once using jubilee clips to squeeze the bush but last time I used poly bushes and never noticed any ride difference,used only to replace the hockey stick bushes I must add.
Click to expand...
Polybushes are the way forward IMHO especially with the likes of the availability of comfort ones etc too takes a lot off effort away from a job and are just as good of not better than rubber bushes
 
tomcat59alan said:
They've obviously tried to replace them before,a right bastid without the proper tool.;) I've done it once using jubilee clips to squeeze the bush but last time I used poly bushes and never noticed any ride difference,used only to replace the hockey stick bushes I must add.
Click to expand...
I'm tempted to go poly, despite the issues I've read about. Which ones did you use?
 
Bern768 said:
It's quite an interesting job I bought my p38 with a leaky diesel pump for 700 quid and done that myself for 35 quid on a genuine seal kit then about a week later my carpet was drenched long story short I would rather dismantle the pump and reassemble it again several times over than do my heater matrix again lol
Click to expand...
I hope you put the Audi LHD matrix in while you had the dash out so you never have to do the o rings again.;)
 
tomcat59alan said:
I hope you put the Audi LHD matrix in while you had the dash out so you never have to do the o rings again.;)
Click to expand...
I didn't, I didn't realise it was conversion that was done till after I done the job unfortunately, but I ended up making part of my dash frame removable to get at it by cutting it and making overlapping sections and now bolts together
 
Bern768 said:
Britpart, superpro any of them are pretty good and shouldn't give you any issues
Click to expand...
Thanks, do you know what the different colours are? The description of the black and the yellow britpart ones are the same :( is it just colour preference?
I can see the polybush brand ones have different colours for different characteristics
 
You must log in or register to reply here.

Similar threads

300bhp/ton
Driven: New Defender - On & Off Road. Is it a Pretender?
2
Replies
29
Views
5K
tottot
tottot
Alibro
Freelander 1 How to fit a 50mm Lift Kit
2 3
Replies
55
Views
33K
Alibro
Alibro
swoggin
How to reduce landy thefts
2 3
Replies
51
Views
11K
RogueTrooper
RogueTrooper
johnny curt 1
how to ... rejouvanate sticky slave cylinders
Replies
2
Views
1K
pobby
pobby
The Mad Hat Man
FBH - all you need to know
Replies
2
Views
34K
Echohowl
E