G

griff2

Active Member
hi all

more ####ing problems lol

right need to change the rubber boot on the cv on the front of my hippo, should be a easy job !!!! but hell no!!!!!

i tried to undo the hub nut :-( and i do mean tried!!!!
i ensure the knock tab was out so nut should come off quit easy ,but hell no!!!!!
the only long rachet i9 had was my trusty torque wrench ,which ive had for years and it has managed to undo anything!!! (i no you should not use them for undoing before anyone says lol)

but after jumping on the ####ing thing it SnApPED !!!!!:mad::mad::mad:
so seeing im in the army next best thing a torque wrench from a TANK!!!!!

only prob was they use inch square sockets not 3/4
so

trusty welder out lol

no way that welds going to fail!!!!

as you can see above its one hell of a torque wrench !!!!! ( i set it too the nm of 400!!!!!)

no joy then 550nm


took it to its max of 800nm!!!!!!!!!!!

and no way the ####ing torque wrench clicked (well it concertinas to be fair)
at 800nm the nut still stays in place!!!!!!!

:mad::mad::mad::mad::mad::mad::mad::mad::mad::mad::mad:

Any ideas?????
 
nuts will split with a chisel ,though my snap-on battery gun just whips them off i cant think ive ever had one that didnt
 
my back hub nut came off quit easy its just this ####er

i have air tools myself ,i will try them next ,if not will try a chisel lol or a blow torch

or if that fails for the first time in 20yrs i may think of going to the garage !!! NOT!!!!! NEVER!!!!! I WILL GET THIS OFF ONE WAY OR ANOTHER!!!!!!!
 
Keep at it mate, you are thinking it through and trying different methods, a garage will end up splitting it off and charging £50...Good luck and keep thread informed :)
 
a garage will just use an impact gun, if that fails they will use heat to get it off. Try chiselling the nut round, sometimes it needs the hammering action to free it off hence the reason just a bar wont always work
 
if its that that you dont try and chisel it round you split it across a flat ,heat will just bugger wheel bearing
 
now now lads he already said he had done it . I know this is not much help to you but I got a three quarter inch extending drive from Machine mart that did the trick try to get somebody to sit in and have there foot on the brake ,now I know it sounds sill but if you are on you own the wheels tend to creep and that gives way a bit . if failing that do you have a large nut splitter ,as you tighten down it splits the nut one side. where abouts are you .if you were close I would bring along that extending bar.
 
kev1nlm said:
a garage will just use an impact gun, if that fails they will use heat to get it off. Try chiselling the nut round, sometimes it needs the hammering action to free it off hence the reason just a bar wont always work
Click to expand...

jamesmartin said:
if its that that you dont try and chisel it round you split it across a flat ,heat will just bugger wheel bearing
Click to expand...

Heat will melt what grease you have in the bearing and melt everything else, if they put that much on it ...and they will coz it's not theirs ...
 
I think at the price of that he would be better scraping it and buying another LOL
 
Last edited:
I had a tough time undoing mine, 3/4" gun wouldn't budge it so I used a breaker bar with a loooong pole. Got in the end
 
They are about the tightest thing on this here earth! Don't really need to be so tight when doing them back up either! I just kept trying with a 4ft bar and snapped one in the process but go there in the end. Failing that have a garage loosen the nut with gun / bar then drive home and finish the job
 
You must log in or register to reply here.

Similar threads

chemmie
Rear wheel hub adventures
Replies
12
Views
1K
chemmie
chemmie
K
Hub nut stuck
Replies
18
Views
851
tottot
tottot
mad85
Disco 2 Front hub/axle seal leaking
Replies
19
Views
1K
mad85
mad85
F
£300 Freelander project! ... my first ever Land Rover
2 3
Replies
44
Views
4K
pwood999
pwood999
Maat
Disco 1 Broken belt pulley bolt - how do I take it out?
Replies
6
Views
1K
Maat
Maat