R

robs

New Member
Hi hopefully this post will help people with a sticking valve. My noise was a loud tick when the motor was warm, it sounded like a leak or cracked exhaust manifold with a loud tapping. Because I occasional get a tappet rattle on cold starts (only 1 or 2 seconds) i thought i would try wynn's hydraulic valve lifter treatment.

Now I am not a big fan of throwing anything down the filler neck apart from good quality oil, so I was skeptical. Anyway warmed my 1997 3.9i V8 LPG up, switched off engine added the treatment. Started the engine up again let it idle with occasional revving for 5-10 min and the tapping noise was still there:(. Went back outside and started the engine 3 hours later and no noise it only went and cured the bloody noise!:)

So far so good the wynns treatment worked for £8.99 from halfrauds and saved me pulling the motor apart. If you have a similar problem it should cure it.
 
td5tool said:
Nice one that's lucky, never had any work for me though
Click to expand...

I was not really expecting it work either but its worth a punt before replacing lifters. However we will see if it continues to work, for all I know it might be a temporary fix. I think I only had 1 sticky tappet but if the whole valvetrain has issues then i doubt it would work. I have 131K on the clock so it might not be long before new camshafts anyway.
 
Last edited:
Drove 20 miles and the noise is back same as before. It sounds just like one tappet we will see if it goes away in the next few hundred miles. Should I worry about 1 tappet that is noisy when warm?
 
m500dpp said:
we had the same on the wifes MX5 - an oil change to 0w-40 Mobil 1 cured it immediately
Click to expand...

I am a big fan 0f Mobil 1 0w-40 but the old v8s prefer thicker oil due to oil pressure. Too thin can = low oil pressure. Its got castrol magnetec 10w - 40 in at the mo.
 
robs said:
Not sure the noise comes from just the n\s valve cover and increases with revs, the o\s is quiet.
Click to expand...

Get a long screwdriver / piece of pipe / extension bar whatever to act as a stethoscope type of thing to transmit the noise, put one end where you think the noise is coming from and the other to your ear or the bone behind your ear -
move it around the engine til you can pin-point the sound a little better and maybe tell the 'type' of tap IYKWIM ...:eek:
 
^ Will do in the morning when its light, the funny thing is the wynn's treatment did make it go away after just a few minutes of idling and i went back and started the car 3 more times the sound had gone, it was not till i drove it did the noise come back.
 
robs said:
I am a big fan 0f Mobil 1 0w-40 but the old v8s prefer thicker oil due to oil pressure. Too thin can = low oil pressure. Its got castrol magnetec 10w - 40 in at the mo.
Click to expand...


Same SAE grade is it not 40, as a multi-grade both are modified to behave like a 40 grade oil at a lower ambient temperature, the Mobil being lower than the Castrol.
 
discool said:
Same SAE grade is it not 40, as a multi-grade both are modified to behave like a 40 grade oil at a lower ambient temperature, the Mobil being lower than the Castrol.
Click to expand...

So can you use 0w-40 in the serpentine 3.9 V* then?
 
Used a stethoscope this morning and the noise is coming from the valve cover about 6 inches back towards the engine from the oil filler neck. Sounds more like a tick than a tap. Any ideas what this might be?
 
robs said:
So can you use 0w-40 in the serpentine 3.9 V* then?
Click to expand...

Why not if you live in the artic, the grade suited for my part of the world is 10w40 as it never gets anywhere below -10c even in the coldest of winters and than only for a few hours, so saying that I could use 15w40 and would be ok as I never had to use my disco from cold at anywhere near -10c :D

New cars with tight tolerance performance engines use low SAE grade oils now, I own a V8 saloon car that uses Mobil 1 of it's equivalent.
 
discool said:
Why not if you live in the artic, the grade suited for my part of the world is 10w40 as it never gets anywhere below -10c even in the coldest of winters and than only for a few hours, so saying that I could use 15w40 and would be ok as I never had to use my disco from cold at anywhere near -10c :D

New cars with tight tolerance performance engines use low SAE grade oils now, I own a V8 saloon car that uses Mobil 1 of it's equivalent.
Click to expand...

I live near Marham in Norfolk and it did get down to minus 13 last winter but generally we are the same temp as you in Kent.

With this in mind do you think putting a 0w-40 oil in will make any difference to the tick. I got a feeling its a worn rocker arm? The tick is more noticeable when warm.
 
robs said:
Used a stethoscope this morning and the noise is coming from the valve cover about 6 inches back towards the engine from the oil filler neck. Sounds more like a tick than a tap. Any ideas what this might be?
Click to expand...

My rebuilt 3.5 used to tick when cold if not used for a few days, it went away sometimes after a few miles and other times after using it a couple of times.
Still don't know what it was:rolleyes:
 
Mine ticks\taps when warm as well as cold just worried it might be oil pressure related. But it does sound like just 1 tappet, stethoscope seems to confirm that. If i had low oil pressure would not both camshafts have noisy tappets? and what other symptoms would I have. I think all vehicles should come out the factory with an oil pressure gauge as standard!
 
You must log in or register to reply here.

Similar threads

M
Engine Rattle/Ticking - TDCI 2.4 2009 DEFENDER 110
Replies
1
Views
584
haza88
haza88
D
Tappets failed
Replies
7
Views
1K
Bobsticle
Bobsticle
J
200 tdi Tapping noise
2
Replies
28
Views
3K
jameslandy
J
E
Auto gearbox woes
Replies
3
Views
664
sierrafery
sierrafery
zooropa1993
Rainers Series 3 from Bremen
Replies
9
Views
725
Flat frog
F