C

Cooperman1

Member
My 1997 300tdi has a strange headlight issue.

The headlights do not work, neither on main beam or dip. Dim dip doesn't work either, but both sidelights are OK.
As soon as I turn the sidelights on the main-beam warning light comes on and stays on when I select main or dip beams..
Looking in the manual, the circuit diagram shows the main beam feed coming from the switch to both LH & RH bulbs and also to the warning light, whilst the dip-beams seem to be from a different circuit.
I suspect the switch is defective, but I would like someone who is more of an electrical expert than I am to give me an opinion.
Thanks in advance.
 
unplug the switch and make a bridge in the plug between the blue/white and brown/green wires( pins 3 - 5) see if you get main beam at the lamps and the warning then and if you do replace the switch, if not then it might become a nightmare (provided the bulbs are not blown)
 
Thanks for this.
The thing that seems most confusing is the fact that the main-beam warning is on all the time, not just on main-beam.
I guess I'll strip the switch out and check it all with my multi-meter.
 
The most confusing is that the warning is on and the lamps are not cos they are on the same feed.,..that's why i recommended that test cos it might be a short and a voltage drop within the switch which can bring on the warning but not stromg enough for the lamps.
 
I have a couple HNCs in mechanical & and electrical engineering but I don’t think that makes me an expert

The D1s electrical system is very straight forward, first of all unplug the dim-dip resistor and leave it unplugged as u don’t need the facility. So, if not all but most, of the issues that u have are with the lighting switch, so get a replacement and hopefully all should be good.
But of course test first :)
 
Sorry to jump in

I fitted the resistor and relay to get the dim dip function, just because it's useful to me, but am I rite in thinking that is known for causing problems as well

Towsey
 
When it cools down a bit I shall borrow a switch from a friend and try replacing it first, after testing the connectivity.

My first thought was the switch, but I thought I would ask you 'Disco Gurus' first.

Thanks for your adice and I'll let you know the result.
 
I finally got round to looking at the problem today. I've been busy doing my Mk.1 Mini Cooper 'S' of late so the Disco took a back seat, but was driveable so it was not a problem.

I stripped the switch out, but could see no issues. I got circuit integrity across the switch with 12 volt power to the headlight fuses. However, I was getting 12 volts to the two main-beam and the two dip-beam fuses all at the same time when I switched the headlights on.

Then I took the connector off of the LH headlight and the plastic connector looked in bad shape with corroded terminals. I cut the connector off and left the wires with no ends then tried the headlights and the RH headlight worked fine. I made up some new direct connectors for the 3 connections, lightly greased and re-connected them.

It all works fine now. The only thing is I still can't work out why the main-beam warning was coming on with the sidelight switch only. But it's all fine now.
Thank you all for your advice.
 
You must log in or register to reply here.

Similar threads

W
My defender thinks it's a police car!
Replies
2
Views
342
vtwin
V
C
Military Series III 109", Dash indicators/switches
Replies
6
Views
2K
marjon
marjon
J
Classic Headlight issues on '92 Classic Hard dash
Replies
1
Views
703
Mark Piercy
Mark Piercy
D
LED front headlamps high beam on dip ??
Replies
18
Views
2K
miktdish
miktdish
H
Indicators not behaving - any ideas?
Replies
6
Views
882
henrythelandy01
H