W

Wolf Pack

Active Member

• Oct 18, 2024

• #1

Morning All,
I have a new Lucas hazard light switch to fit and the MoD manual says that I need to change the bulb out for a 24v version to match my electrics.

I can't see a way to get inside this thing.

Any advice very much appreciated.

 

Attachments

• 
  A Wolf hazard switch.jpeg

  231.9 KB · Views: 21

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #2

Wolf Pack said:

Morning All,
I have a new Lucas hazard light switch to fit and the MoD manual says that I need to change the bulb out for a 24v version to match my electrics.

I can't see a way to get inside this thing.

Any advice very much appreciated.

Click to expand...

The front comes off.2 very thin items to prise the left/right at the middle of the switch
Face comes off to show bulb.
My bulb does not flash but trailer light shows up as the warning lamp

 

W

Wolf Pack

Active Member

• Oct 18, 2024

• #3

Hicap phill said:

The front comes off.2 very thin items to prise the left/right at the middle of the switch
Face comes off to show bulb.
My bulb does not flash but trailer light shows up as the warning lamp

Click to expand...

Do you mean prising these gaps apart?

 

Attachments

• 
  A Wolf hazard rear.jpeg

  120.5 KB · Views: 14

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #4

Wolf Pack said:

Do you mean prising these gaps apart?

Click to expand...

Just been out to mine for photos..
Screw drivers into front by rocker point

Prise a bit to see holes where the rocker is

Face should now pull off

Hope this helps

 

W

Wolf Pack

Active Member

• Oct 18, 2024

• #5

Thank you very much.
The switch face is on U-shaped lugs then?

 

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #6

Wolf Pack said:

Thank you very much.
The switch face is on U-shaped lugs then?

Click to expand...

Yes.
You can see each side of the bulb where the lugs line up

 

W

Wolf Pack

Active Member

• Oct 18, 2024

• #7

Hicap phill said:

Yes.
You can see each side of the bulb where the lugs line up

Click to expand...

Thanks again.
Do you happen got know the colour of the 2 wires that connect on either side of that switch?

 

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #8

Wolf Pack said:

Thanks again.
Do you happen got know the colour of the 2 wires that connect on either side of that switch?

Click to expand...

Nope….
Are they earths?
Unsure if mine are connected(if I get chance I will remove panel)

 

W

Wolf Pack

Active Member

• Oct 18, 2024

• #9

My immediate and dangerous assumption was that they are power and earth for that bulb.

 

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #10

Wolf Pack said:

My immediate and dangerous assumption was that they are power and earth for that bulb.

Click to expand...

Could be. Unsure what the plugs supply’s,may be just the indication & dash warning light

 

H

Hicap phill

Well-Known Member

• Oct 18, 2024

• #11

Just took a photo through the hole next to the switch. Looks like brown & red to 1 side.

 

W

Wolf Pack

Active Member

• Oct 18, 2024

• #12

Hicap phill said:

Could be. Unsure what the plugs supply’s,may be just the indication & dash warning light

Click to expand...

Yes, good point. An earth would be black from what I have gathered so far.

 

W

Wolf Pack

Active Member

• Monday at 07:06

• #13

After a process of deduction and them being the only 2 wires "in that area", I have to assume that these black & white and the plain black wires must be the power for the hazard switch bulb, or is that just too dangerous an assumption?

 

Attachments

• 
  A Wolf 2 wires.jpeg

  202.7 KB · Views: 4